SAM3N2C Atmel Corporation, SAM3N2C Datasheet - Page 319

• Manufacturer Part Number: SAM3N2C
• Manufacturer: Atmel Corporation

Specifications of SAM3N2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 48 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 47
• Ext Interrupts: 47
• Quadrature Decoder Channels: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

22. Peripheral DMA Controller (PDC)
22.1
22.2
11011A–ATARM–04-Oct-10
Description
Embedded Characteristics
The Peripheral DMA Controller (PDC) transfers data between on-chip serial peripherals and the
on- and/or off-chip memories. The link between the PDC and a serial peripheral is operated by
the AHB to ABP bridge.
The user interface of each PDC channel is integrated into the user interface of the peripheral it
serves. The user interface of mono directional channels (receive only or transmit only), contains
two 32-bit memory pointers and two 16-bit counters, one set (pointer, counter) for current trans-
fer and one set (pointer, counter) for next transfer. The bi-directional channel user interface
contains four 32-bit memory pointers and four 16-bit counters. Each set (pointer, counter) is
used by current transmit, next transmit, current receive and next receive.
Using the PDC removes processor overhead by reducing its intervention during the transfer.
This significantly reduces the number of clock cycles required for a data transfer, which
improves microcontroller performance.
To launch a transfer, the peripheral triggers its associated PDC channels by using transmit and
receive signals. When the programmed data is transferred, an end of transfer interrupt is gener-
ated by the peripheral itself.
The Peripheral DMA Controller handles transfer requests from the channel according to the fol-
lowing priorities (Low to High priorities):
Table 22-1.
Instance name
• Handles data transfer between peripherals and memories
• Low bus arbitration overhead
• Next Pointer management for reducing interrupt latency requirement
USART0
USART0
UART0
UART0
– One Master Clock cycle needed for a transfer from memory to peripheral
– Two Master Clock cycles needed for a transfer from peripheral to memory
TWI0
TWI0
ADC
DAC
SPI
SPI
Peripheral DMA Controller
Channel T/R
Transmit
Transmit
Transmit
Transmit
Transmit
Receive
Receive
Receive
Receive
Receive
100 & 64 Pins
x
x
x
x
x
x
x
x
x
x
48 Pins
N/A
x
x
x
x
x
x
x
x
x
SAM3N
319