SAM9261 Atmel Corporation, SAM9261 Datasheet - Page 545

• Manufacturer Part Number: SAM9261
• Manufacturer: Atmel Corporation

Specifications of SAM9261

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 160
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

35.7
6062N–ATARM–3-Oct-11
MultiMedia Card Operations
Table 35-3.
Notes:
Figure 35-6. SD Card Bus Connections with One Slot
Note:
When the MCI is configured to operate with SD memory cards, the width of the data bus can be
selected in the MCI_SDCR register. Clearing the SDCBUS bit in this register means that the
width is one bit; setting it means that the width is four bits. In the case of multimedia cards, only
the data line 0 is used. The other data lines can be used as independent PIOs.
After a power-on reset, the cards are initialized by a special message-based MultiMedia Card
bus protocol. Each message is represented by one of the following tokens:
Card addressing is implemented using a session address assigned during the initialization
phase by the bus controller to all currently connected cards. Their unique CID number identifies
individual cards.
The structure of commands, responses and data blocks is described in the MultiMedia-Card
System Specification. See also
MultiMediaCard bus data transfers are composed of these tokens.
There are different types of operations. Addressed operations always contain a command and a
response token. In addition, some operations have a data token; the others transfer their infor-
mation directly within the command or response structure. In this case, no data token is present
Pin Number
7
8
9
• Command: A command is a token that starts an operation. A command is sent from the host
• Response: A response is a token which is sent from an addressed card or (synchronously)
• Data: Data can be transferred from the card to the host or vice versa. Data is transferred via
either to a single card (addressed command) or to all connected cards (broadcast
command). A command is transferred serially on the CMD line.
from all connected cards to the host as an answer to a previously received command. A
response is transferred serially on the CMD line.
the data line.
1. I: input, O: output, PP: Push Pull, OD: Open Drain.
2. When several MCI (x MCI) are embedded in a product, MCCK refers to MCIx_CK, MCCDA to
When several MCI (x MCI) are embedded in a product, MCCK refers to MCIx_CK, MCCDA to
MCIx_CDA MCDAy to MCIx_DAy.
MCIx_CDA, MCDAy to MCIx_DAy.
SD Memory Card Bus Signals (Continued)
Name
DAT[0]
DAT[1]
DAT[2]
MCDA0 - MCDA3
MCCDA
MCCK
Type
I/O/PP
I/O/PP
I/O/PP
Table 35-4 on page
(1)
Description
Data line Bit 0
Data line Bit 1
Data line Bit 2
546.
SD CARD
AT91SAM9261
MCI Pin Name
(Slot z)
MCDz0
MCDz1
MCDz2
(2)
545