SAM3A8C Atmel Corporation, SAM3A8C Datasheet - Page 996
SAM3A8C
Manufacturer Part Number
SAM3A8C
Description
Manufacturer
Atmel Corporation
- Current page: 996 of 1465
- Download datasheet (26Mb)
996
996
SAM3X/A
SAM3X/A
current level of the fault inputs by means of the field FIV, and can know which fault is currently
active thanks to the FS field.
Each fault can be taken into account or not by the fault protection mechanism in each channel.
To be taken into account in the channel x, the fault y must be enabled by the bit FPEx[y] in the
“PWM Fault Protection Enable Registers” (PWM_FPE1/2). However the synchronous channels
(see
of the channel 0 (bits FPE0[y]).
The fault protection on a channel is triggered when this channel is enabled and when any one of
the faults that are enabled for this channel is active. It can be triggered even if the PWM master
clock (MCK) is not running but only by a fault input that is not glitch filtered.
When the fault protection is triggered on a channel, the fault protection mechanism forces the
channel outputs to the values defined by the fields FPVHx and FPVLx in the
tion Value Register”
forcing is made asynchronously to the channel counter.
CAUTION:
If a comparison unit is enabled (see
triggered in the channel 0, in this case the comparison cannot match.
As soon as the fault protection is triggered on a channel, an interrupt (different from the interrupt
generated at the end of the PWM period) can be generated but only if it is enabled and not
masked. The interrupt is reset by reading the interrupt status register, even if the fault which has
caused the trigger of the fault protection is kept active.
• To prevent an unexpected activation of the status flag FSy in the PWM_FSR register, the
• To prevent an unexpected activation of the Fault Protection on the channel x, the bit FPEx[y]
FMODy bit can be set to “1” only if the FPOLy bit has been previously configured to its final
value.
can be set to “1” only if the FPOLy bit has been previously configured to its final value.
Section 38.6.2.7 “Synchronous
(PWM_FPV) and leads to a reset of the counter of this channel. The output
Channels”) do not use their own fault enable bits, but those
Section 38.6.3 “PWM Comparison
Units”) and if a fault is
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
“PWM Fault Protec-
Related parts for SAM3A8C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: