PIC16C620 Microchip Technology, PIC16C620 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC16C620
Manufacturer Part Number
PIC16C620
Description
EPROM-Based 8-Bit CMOS Microcontroller
Manufacturer
Microchip Technology
Datasheet
1.PIC16C620.pdf
(108 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16C620-04/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC16C620/JW
Manufacturer:
MICROCH
Quantity:
20 000
Part Number:
PIC16C620A-04/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC16C620A-04/SO
Manufacturer:
MICROCHI
Quantity:
84
Part Number:
PIC16C620A-04/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC16C620A-04I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC16C620A-04I/SS
Manufacturer:
Microchip Technology
Quantity:
135
Company:
Part Number:
PIC16C620A-40/P
Manufacturer:
Microchip Technology
Quantity:
135
PIC16C62X
4.2.2.1
The STATUS register, shown in Figure 4-8, contains
the arithmetic status of the ALU, the RESET status and
the bank select bits for data memory.
The STATUS register can be the destination for any
instruction, like any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
For example, CLRF STATUS will clear the upper-three
bits and set the Z bit. This leaves the status register as
000uu1uu (where u = unchanged).
FIGURE 4-8:
DS30235G-page 18
Reserved Reserved
bit7
bit 7:
bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing)
bit 4:
bit 3:
bit 2:
bit 0:
bit 1:
IRP
STATUS REGISTER
IRP: Register Bank Select bit (used for indirect addressing)
1 = Bank 2, 3 (100h - 1FFh)
0 = Bank 0, 1 (00h - FFh)
The IRP bit is reserved on the PIC16C62X, always maintain this bit clear.
11 = Bank 3 (180h - 1FFh)
10 = Bank 2 (100h - 17Fh)
01 = Bank 1 (80h - FFh)
00 = Bank 0 (00h - 7Fh)
Each bank is 128 bytes. The RP1 bit is reserved on the PIC16C62X, always maintain this bit clear.
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)(for borrow the polarity is reversed)
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)
1 = A carry-out from the most significant bit of the result occurred
0 = No carry-out from the most significant bit of the result occurred
Note: For borrow the polarity is reversed. A subtraction is executed by adding the two’s complement of the
second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of
the source register.
RP1
STATUS REGISTER (ADDRESS 03H OR 83H)
R/W-0
RP0
R-1
TO
R-1
PD
Preliminary
R/W-x
Z
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register because these instructions do not
affect any status bit. For other instructions, not affecting
any status bits, see the “Instruction Set Summary”.
Note 1:
Note 2:
R/W-x
DC
The IRP and RP1 bits (STATUS<7:6>)
are not used by the PIC16C62X and
should be programmed as ’0'. Use of
these bits as general purpose R/W bits
is NOT recommended, since this may
affect upward compatibility with future
products.
The C and DC bits operate as a Borrow
and Digit Borrow out bit, respectively, in
subtraction. See the SUBLW and SUBWF
instructions for examples.
R/W-x
C
bit0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
- n = Value at POR reset
-x = Unknown at POR reset
1998 Microchip Technology Inc.
read as ‘0’