PIC16C620 Microchip Technology, PIC16C620 Datasheet - Page 51

• Manufacturer Part Number: PIC16C620
• Description: EPROM-Based 8-Bit CMOS Microcontroller
• Manufacturer: Microchip Technology

9.4.5
On power-up the time-out sequence is as follows: First
PWRT time-out is invoked after POR has expired. Then
example, in RC mode with PWRTE bit erased (PWRT
disabled), there will be no time-out at all. Figure 9-9,
Figure 9-10
sequences.
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, the time-outs will expire. Then
bringing MCLR high will begin execution immediately
(see Figure 9-10). This is useful for testing purposes or
to synchronize more than one PIC16C62X device oper-
ating in parallel.
Table 9-6 shows the reset conditions for some special
registers, while Table 9-7 shows the reset conditions for
TABLE 9-3:
TABLE 9-4:
Legend: u = unchanged, x = unknown
TABLE 9-5:
OST is activated. The total time-out will vary based on
oscillator configuration and PWRTE bit status. For
all the registers.
Address Name
83h
8Eh
Note1: Other (non power-up) resets include MCLR reset, Brown-out Reset and Watchdog Timer Reset during normal operation.
1998 Microchip Technology Inc.
Oscillator Configuration
POR
0
0
0
1
1
1
1
1
TIME-OUT SEQUENCE
STATUS
PCON
XT, HS, LP
RC
BOR
and
X
X
X
0
1
1
1
1
TIME-OUT IN VARIOUS SITUATIONS
STATUS/PCON BITS AND THEIR SIGNIFICANCE
SUMMARY OF REGISTERS ASSOCIATED WITH BROWN-OUT
Bit 7
—
Figure 9-11
TO
1
0
X
X
0
0
u
1
Bit 6
—
72 ms + 1024 T
PWRTE = 0
depict
PD
1
X
0
X
u
0
u
0
Bit 5
72 ms
—
Power-on-reset
Illegal, TO is set on POR
Illegal, PD is set on POR
Brown-out Reset
WDT Reset
WDT Wake-up
MCLR reset during normal operation
MCLR reset during SLEEP
time-out
Bit 4
OSC
Power-up
TO
—
Preliminary
Bit 3
PD
—
PWRTE = 1
1024 T
9.4.6
The power control/status register, PCON (address
8Eh) has two bits.
Bit0 is BOR (Brown-out). BOR is unknown on
power-on-reset. It must then be set by the user and
checked on subsequent resets to see if BOR = 0
indicating that a brown-out has occurred. The BOR
status bit is a don’t care and is not necessarily
predictable if the brown-out circuit is disabled (by
setting BOREN bit = 0 in the Configuration word).
Bit1 is POR (Power-on-reset). It is a ‘0’ on
power-on-reset and unaffected otherwise. The user
must write a ‘1’ to this bit following a power-on-reset.
On a subsequent reset if POR is ‘0’, it will indicate that
a power-on-reset must have occurred (V
gone too low).
—
Bit 2
OSC
—
POWER CONTROL (PCON)/
STATUS REGISTER
Bit 1
POR
72 ms + 1024 T
Brown-out Reset
Bit 0
BOR
72 ms
PIC16C62X
Value on POR
0001 1xxx
---- --0x
OSC
Reset
DS30235G-page 51
from SLEEP
1024 T
DD
Wake-up
other resets
Value on all
000q quuu
---- --uq
may have
—
OSC
(1)