MT9074 Mitel Networks Corporation, MT9074 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
MT9074
Manufacturer Part Number
MT9074
Description
T1/E1/J1 Single Chip Transceiver
Manufacturer
Mitel Networks Corporation
Datasheet
1.MT9074.pdf
(122 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT9074AL
Manufacturer:
ZARLINK
Quantity:
1 238
Company:
Part Number:
MT9074AL1
Manufacturer:
ZARLINK
Quantity:
22
Company:
Part Number:
MT9074AP
Manufacturer:
MITEL
Quantity:
14
Part Number:
MT9074AP
Manufacturer:
ZARLINK
Quantity:
20 000
Company:
Part Number:
MT9074AP1
Manufacturer:
ZARLINK
Quantity:
227
Company:
Part Number:
MT9074APR1
Manufacturer:
ZARLINK
Quantity:
227
Advance Information
G.704 and G.732 for more details on CAS
multiframing requirements.
A CAS signalling multiframe consists of 16 basic
frames (numbered 0 to 15), which results in a
multiframe repetition rate of 2 msec. It should be
noted
multiframe may be completely distinct from those of
the CRC-4 multiframe. CAS multiframe alignment is
based on a multiframe alignment signal (a 0000 bit
sequence), which occurs in the most significant
nibble of time slot 16 of basic frame 0 of the CAS
multiframe. Bit 6 of this time slot is the multiframe
alarm bit (usually designated Y). When CAS
multiframing is acquired on the receive side, the
transmit Y-bit is zero; when CAS multiframing is not
acquired, the transmit Y-bit is one. Bits 5, 7 and 8
(usually designated X) are spare bits and are
normally set to one if not used.
Time slot 16 of the remaining 15 basic frames of the
CAS multiframe (i.e., basic frames 1 to 15) are
reserved for the ABCD signalling bits for the 30
payload channels. The most significant nibbles are
reserved for channels 1 to 15 and the least
significant nibbles are reserved for channels 16 to
30. That is, time slot 16 of basic frame 1 has ABCD
for channel 1 and 16, time slot 16 of basic frame 2
has ABCD for channel 2 and 17, through to time slot
16 of basic frame 15 has ABCD for channel 15 and
30.
00000001 (01H)
00000010 (02H)
00000011 (03H)
00000100 (04H)
00000101 (05H)
00000110 (06H)
00000111 (07H)
00001000 (08H)
00001001 (09H)
00001010 (0AH)
00001011 (0BH)
00001011 (0CH)
Page Address
that
D
7
- D
the
0
boundaries
Master
Control
Master
Per Channel Transmit Signalling
Per Channel Transmit Signalling
Per Time Slot Control
Per Time Slot Control
Per Channel Receive Signalling
Per Channel Receive Signalling
HDLC0 Control and Status
HDLC1 Control and Status
Status
of
the
Register Description
Table 13 - Page Summary
signalling
MT9074 Access and Control
The Control Port Interface
The control and status of the MT9074 is achieved
through a non-multiplexed parallel microprocessor
port. The parallel port may be configured for
Motorola style control signals (by setting pin INT/
MOT low) or Intel style control signals (by setting pin
INT/MOT high).
Control and Status Register Access
The controlling microprocessor gains access to
specific registers of the MT9074 through a two step
process. First, writing to the Command/Address
Register (CAR) selects one of the 15 pages of
control and status registers (CAR address: AC4 = 0,
AC3-AC0 = don't care, CAR data D7 - D0 = page
number). Second, each page has a maximum of 16
registers that are addressed on a read or write to a
non-CAR address (non-CAR: address AC4 = 1, AC3-
AC0 = register address, D7-D0 = data). Once a page
of memory is selected, it is only necessary to write to
the CAR when a different page is to be accessed.
See the AC Electrical Characteristics section.
Please note that for microprocessors with read/write
cycles less than 200 ns, a wait state or a dummy
operation
(for
C
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Processor
programming)
Access
CSTi
CSTi
CSTo
CSTo
---
---
- - -
- - -
- - -
- - -
between
MT9074
ST-BUS
Access
two
19