MT9074 Mitel Networks Corporation, MT9074 Datasheet - Page 80
![no-image](/images/no-image-200.jpg)
MT9074
Manufacturer Part Number
MT9074
Description
T1/E1/J1 Single Chip Transceiver
Manufacturer
Mitel Networks Corporation
Datasheet
1.MT9074.pdf
(122 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT9074AL
Manufacturer:
ZARLINK
Quantity:
1 238
Company:
Part Number:
MT9074AL1
Manufacturer:
ZARLINK
Quantity:
22
Company:
Part Number:
MT9074AP
Manufacturer:
MITEL
Quantity:
14
Part Number:
MT9074AP
Manufacturer:
ZARLINK
Quantity:
20 000
Company:
Part Number:
MT9074AP1
Manufacturer:
ZARLINK
Quantity:
227
Company:
Part Number:
MT9074APR1
Manufacturer:
ZARLINK
Quantity:
227
MT9074
80
6-5
Bit
7
4
3
2
1
0
Table 96 - Configuration Control Word
ADSEQ Digital Milliwatt or Digital Test
LIUEn
Name
T1/E1
ELOS
RSV
RSV
RSV
(Page 2, Address 10H) (E1)
E1 mode selection. when this bit is
one, the device is in E1 mode.
Reserved. Must be kept at 0 for
normal operation.
LIU Enable.Setting this bit low
enables the internal LIU front-end.
Setting this pin high disables the
LIU. Digital inputs RXA and RXB are
sampled by the rising edge of E2.0i
(C1.50) to strobe in the received line
data. Digital transmit data is clocked
out of pins TXA and TXB with the
rising edge of C2.0o
ELOS Enable. Set this bit low to set
the analog loss of signal threshold to
40 dB below nominal. Set this bit
high to set the analog loss of signal
threshold to 20 dB below nominal.
Reserved. Must be kept at 0 for
normal operation.
Sequence. If one, the A-law digital
milliwatt analog test sequence will
be selected by the Per Time Slot
Control bits TTST and RTST.If zero,
a PRBS generator / detector will be
connected to channels with TTST,
RRST respectively
Reserved. Must be kept at 0 for
normal operation.
Functional Description
6-4
2-0
6-0 CP6-0 Custom Pulse. These bits provide the
Bit
Bit
7
3
7
Name
Name
RSV
RSV
RSV
RSV
CPL
Table 97 - Custom Tx Pulse Enable
Table 98 - Custom Pulse Word 1
(Page 2, Address 1CH) (E1)
(Page 2, Address 11H) (E1)
Reserved. Must be kept high for
normal operation.
Reserved. Must be kept low for normal
operation.
Custom Pulse Level. Setting this bit
low enables the internal ROM values in
generating the transmit pulses. The
ROM is coded for different line
terminations or build out, as specified
in the LIU Control word. Setting this bit
high disables the pre-programmed
pulse templates. Each of the 4 phases
that generate a mark derive their D/A
coefficients
programmed in the CPW registers.
Reserved. Must be kept at 0 for normal
operation.
Reserved. Must be kept at 0 for normal
operation.
capability
magnitude setting for the TTIP/TRING
line driver A/D converter during the first
phase of a mark. The greater the
binary number loaded into the register,
the greater the amplitude driven out.
This feature is enabled when the
control bit 3 - CPL of the Custom Tx
Pulse Enable Register - address 11H
of Page 2 is set high.
Functional Description
Functional Description
Advance Information
for
from
programming
the
values
the