AD9251BCPZRL7 Analog Devices, Inc., AD9251BCPZRL7 Datasheet - Page 34
![no-image](/images/no-image-200.jpg)
AD9251BCPZRL7
Manufacturer Part Number
AD9251BCPZRL7
Description
14-bit, 20 Msps/40 Msps/65 Msps/80 Msps, 1.8 V Dual Analog-to-digital Converter
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD9251BCPZRL7.pdf
(36 pages)
AD9251
APPLICATIONS INFORMATION
DESIGN GUIDELINES
Before starting design and layout of the AD9251 as a system,
it is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements needed for certain pins.
Power and Ground Recommendations
When connecting power to the AD9251, it is strongly
recommended that two separate supplies be used. Use one 1.8 V
supply for analog (AVDD); use a separate 1.8 V to 3.3 V supply for
the digital outputs (DRVDD). If a common 1.8 V AVDD and
DRVDD supply must be used, the AVDD and DRVDD domains
must be isolated with a ferrite bead or filter choke and separate
decoupling capacitors. Several different decoupling capacitors
can be used to cover both high and low frequencies. Locate
these capacitors close to the point of entry at the PCB level and
close to the pins of the part, with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9251. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
is easily achieved.
Exposed Paddle Thermal Heat Sink Recommendations
The exposed paddle (Pin 0) is the only ground connection for
the AD9251 and therefore it must be connected to analog
ground (AGND) on the customer’s PCB. To achieve the best
electrical and thermal performance, mate an exposed (no solder
mask) continuous copper plane on the PCB to the AD9251
exposed paddle, Pin 0.
Rev. PrH | Page 34 of 36
The copper plane should have several vias to achieve the lowest
possible resistive thermal path for heat dissipation to flow through
the bottom of the PCB. Fill or plug these vias with nonconductive
epoxy.
To maximize the coverage and adhesion between the ADC and
the PCB, a silkscreen should be overlaid to partition the continuous
plane on the PCB into several uniform sections. This provides
several tie points between the ADC and the PCB during the reflow
process. Using one continuous plane with no partitions guarantees
only one tie point between the ADC and the PCB. For detailed
information about packaging and PCB layout of chip scale
packages, see the AN-772 Application Note, A Design and
Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP) at www.analog.com.
VCM
The VCM pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 34.
RBIAS
The AD9251 requires that a 10 kΩ resistor be placed between
the RBIAS pin and ground. This resistor sets the master current
reference of the ADC core and should have at least a 1% tolerance.
Reference Decoupling
Externally decoupled the VREF pin to ground with a low ESR,
1.0 μF capacitor in parallel with a low ESR, 0.1 μF ceramic
capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CS, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9251 to keep these signals from transitioning at the converter
inputs during critical sampling periods.
Preliminary Technical Data