PCF8811U/2DA/1 NXP [NXP Semiconductors], PCF8811U/2DA/1 Datasheet - Page 28
PCF8811U/2DA/1
Manufacturer Part Number
PCF8811U/2DA/1
Description
80 x 128 pixels matrix LCD driver
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.PCF8811U2DA1.pdf
(81 pages)
- Current page: 28 of 81
- Download datasheet (441Kb)
NXP Semiconductors
PCF8811_4
Product data sheet
Fig 19. Read mode SPI 3-line and 4-line
SDATA
SCLK
SDO
SCE
RES
10.1.2 Read mode (only extended command set)
10.2.1 Write mode
10.2 Serial interface (3-line)
DB7 DB6 DB5 DB4
The read mode of the interface means that the microcontroller reads data from the
PCF8811. To do so, the microcontroller first has to send a command (the read status
command) and then the PCF8811 will respond by transmitting data on the SDO line. After
that, SCE is required to go HIGH; see
The PCF8811 samples the SDATA data on rising SCLK edges, but shifts SDO data on
falling SCLK edges. So, the microcontroller is supposed to read SDO data on rising SCLK
edges.
After the read status command has been sent, the SDATA line must be set to 3-state not
later then the falling SCLK edge of the last bit; see
Serial interface timing diagrams are shown in
The serial interface is also a 3-line bidirectional interface for communication between the
microcontroller and the LCD driver chip. The 3 lines are:
The PCF8811 is connected to the SDA of the microcontroller by two lines: SDATA (data
input) and SDO (data output) which are connected together.
The write mode of the interface means that the microcontroller writes commands and data
to the PCF8811. Each data packet contains a control bit (D/C) and a transmission byte. If
D/C is LOW, the following byte is interpreted as a command byte. The instruction set is
shown in
After every data byte the address counter is incremented automatically.
the general format of the write mode and the definition of the transmission byte.
•
•
•
SCE (chip enable)
SCLK (serial clock)
SDATA (serial data)
Table
instruction
10. If D/C is HIGH, the following byte is stored in the display data RAM.
DB3
DB2
Rev. 04 — 27 June 2008
DB1 DB0
DB7 DB6 DB5 DB4 DB3
Figure
19.
Section
read out data
Figure
16.2.
80 x 128 pixels matrix LCD driver
DB2
19.
DB1 DB0
PCF8811
© NXP B.V. 2008. All rights reserved.
Figure 20
mgw748
shows
28 of 81
Related parts for PCF8811U/2DA/1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: