FDC37B787QF SMSC [SMSC Corporation], FDC37B787QF Datasheet - Page 56
FDC37B787QF
Manufacturer Part Number
FDC37B787QF
Description
Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.FDC37B787QF.pdf
(249 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 56 of 249
- Download datasheet (881Kb)
DATA TRANSFER COMMANDS
All of the Read Data, Write Data and Verify type
commands use the same parameter bytes and
return the same results information, the only
difference being the coding of bits 0-4 in the first
byte.
An implied seek will be executed if the feature was
enabled by the Configure command. This seek is
completely transparent to the user. The Drive Busy
bit for the drive will go active in the Main Status
Register during the seek portion of the command.
If the seek portion fails, it is reflected in the results
status normally returned for a Read/Write Data
command. Status Register 0 (ST0) would contain
the error code and C would contain the cylinder on
which the seek failed.
Read Data
A set of nine (9) bytes is required to place the FDC
in the Read Data Mode.
command has been issued, the FDC loads the
head (if it is in the unloaded state), waits the
specified head settling time (defined in the Specify
command),
and
begins
After the Read Data
reading
00
01
02
03
07
N
..
TABLE 23 - SECTOR SIZES
ID
56
SECTOR SIZE
1024 bytes
16 Kbytes
128 bytes
256 bytes
512 bytes
Address Marks and ID fields. When the sector
address read off the diskette matches with the
sector address specified in the command, the FDC
reads the sector's data field and transfers the data
to the FIFO.
After completion of the read operation from the
current sector, the sector address is incremented
by one and the data from the next logical sector is
read and output via the FIFO. This continuous
read
Operation". Upon receipt of TC, or an implied TC
(FIFO overrun/underrun), the FDC stops sending
data but will continue to read data from the current
sector, check the CRC bytes, and at the end of the
sector, terminate the Read Data Command. N
determines the number of bytes per sector (see
Table 23 below). If N is set to zero, the sector size
is set to 128.
number of bytes to be transferred. If DTL is less
than 128, the FDC transfers the specified number
of bytes to the host. For reads, it continues to
read the entire 128-byte sector and checks for
CRC errors. For writes, it completes the 128-byte
sector by filling in zeros. If N is not set to 00 Hex,
DTL should be set to FF Hex and has no impact
on the number of bytes transferred.
...
function
is
The DTL value determines the
called
"Multi-Sector
Read
Related parts for FDC37B787QF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: