SST49LF016C-33-4C-WHE Microchip Technology, SST49LF016C-33-4C-WHE Datasheet - Page 8
![IC FLASH SER LPC 16MBIT 32TSOP](/photos/16/11/161142/sst49lf016c_sml.jpg)
SST49LF016C-33-4C-WHE
Manufacturer Part Number
SST49LF016C-33-4C-WHE
Description
IC FLASH SER LPC 16MBIT 32TSOP
Manufacturer
Microchip Technology
Datasheets
1.SST49LF080A-33-4C-NHE.pdf
(2 pages)
2.SST49LF080A-33-4C-NHE.pdf
(2 pages)
3.SST49LF016C-33-4C-NHE.pdf
(36 pages)
Specifications of SST49LF016C-33-4C-WHE
Memory Type
FLASH
Memory Size
16M (2M x 8)
Operating Temperature
0°C ~ 85°C
Package / Case
32-TSOP
Format - Memory
FLASH
Speed
33MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Data Bus Width
8 bit
Architecture
Sectored
Interface Type
Parallel, Serial
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Maximum Operating Current
18 mA
Mounting Style
SMD/SMT
Organization
4 KB x 512
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SST49LF016C-33-4C-WHE
Manufacturer:
Microchip Technology
Quantity:
135
Data Sheet
Clock
The LCLK pin accepts a clock input from the host controller.
Input/Output Communications
The LAD[3:0] pins are used to serially communicate cycle
information such as cycle type, cycle direction, ID selection,
address, data, and sync fields.
Input Communication Frame
The LFRAME# pin is used to indicate start of a LPC bus
cycle. The pin is also used to abort an LPC bus cycle in
progress.
Reset
A V
and RST# pins have the same function internally. It is
required to drive INIT# or RST# pins low during a system
reset to ensure proper CPU initialization. During a Read
operation, driving INIT# or RST# pins low deselects the
device and places the output drivers, LAD[3:0], in a high
impedance state. The reset signal must be held low for a
minimum of time T
cedure is performed during a Program or Erase operation.
See Table 25, Reset Timing Parameters, for more informa-
tion. A device reset during an active Program or Erase oper-
ation will abort the operation and memory contents may
become invalid due to data being altered or corrupted from
an incomplete Erase or Program operation.
Identification Inputs
These pins are part of a mechanism that allows multiple
devices to be attached to the same bus. The strapping of
these pins is used to identify the component. The boot
device must have ID[3:0] = 0; all subsequent devices
should use sequential count-up strapping. These pins are
internally pulled-down with a resistor between 20-100 K
General Purpose Inputs
The General Purpose Inputs (GPI[4:0]) can be used as dig-
ital inputs for the CPU to read. The GPI register holds the
values on these pins. The data on the GPI pins must be
stable before the start of a GPI register Read and remain
stable until the Read cycle is complete. The pins must be
driven low, V
©2008 Silicon Storage Technology, Inc.
IL
on INIT# or RST# pin initiates a device reset. INIT#
IL
, or high, V
RSTP .
A reset latency occurs if a reset pro-
IH
but not left unconnected (float).
Ω
.
8
Write Protect / Top Block Lock
The Top Boot Lock (TBL#) and Write Protect (WP#/AAI)
pins are provided for hardware write protection of device
memory in the SST49LF016C. The TBL# pin is used to
write protect 16 KByte at the highest memory address
range for the SST49LF016C. WP#/AAI pin write protects
the remaining sectors in the flash memory. An active low
signal at the TBL# pin prevents Program and Erase opera-
tions of the top Boot Block. When TBL# pin is held high,
write protection of the top Boot Block is then determined by
the Boot Block Locking registers. The WP#/AAI pin serves
the same function for the remaining sectors of the device
memory. The TBL# and WP#/AAI pins write protection
functions operate independently of one another. Both TBL#
and WP#/AAI pins must be set to their required protection
states prior to starting a Program or Erase operation. A
logic level change occurring at the TBL# or WP#/AAI pin
during a Program or Erase operation could cause unpre-
dictable results. TBL# and WP#/AAI pins cannot be left
unconnected.
TBL# is internally OR’ed with the top Boot Block Locking
register. When TBL# is low, the top Boot Block is hardware
write protected regardless of the state of the Write-Lock bit
for the Boot Block Locking register. Clearing the Write-Pro-
tect bit in the register when TBL# is low will have no func-
tional effect, even though the register may indicate that the
block is no longer locked.
WP#/AAI is internally OR’ed with the Block Locking regis-
ter. When WP#/AAI is low, the blocks are hardware write
protected regardless of the state of the Write-Lock bit for
the corresponding Block Locking registers. Clearing the
Write-Protect bit in any register when WP#/AAI is low will
have no functional effect, even though the register may indi-
cate that the block is no longer locked.
AAI Enable
The AAI Enable pin (WP#/AAI) is used to enable the Auto
Address Increment (AAI) mode. When the WP#/AAI pin is
set to the Supervoltage V
mode with Multi-Byte programming. When the WP#/AAI
pin is brought to V
mode.
Ready/Busy
The Ready/Busy pin (RY/BY#), is an open drain output
which indicates the device is ready to accept data in an AAI
mode, or that the internal programming cycle is complete.
The pin is used in conjunction with the LD# pin to switch
between these two flag states (see Table 18).
IL
/V
16 Mbit LPC Serial Flash
IH
levels, the device returns to LPC
H
(9±0.5V), the device is in AAI
SST49LF016C
S71237-08-000
5/08