AT25DF321A-SH-T Atmel, AT25DF321A-SH-T Datasheet - Page 34

• Manufacturer Part Number: AT25DF321A-SH-T
• Description: IC FLASH 32MBIT 100MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT25DF321A-SH-T

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 32M (16384 pages x 256 Bytes)
• Speed: 100MHz
• Interface: SPI, RapidS
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Density: 32Mb
• Access Time (max): 5ns
• Interface Type: Serial (SPI)
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: SOIC
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 4M
• Supply Current: 19mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.2
34
Write Status Register Byte 1
The Write Status Register Byte 1 command is used to modify the SPRL bit of the Status Register and/or to perform a
Global Protect or Global Unprotect operation. Before the Write Status Register Byte 1 command can be issued, the Write
Enable command must have been previously issued to set the WEL bit in the Status Register to a logical “1”.
To issue the Write Status Register Byte 1 command, the CS pin must first be asserted and the opcode of 01h must be
clocked into the device followed by one byte of data. The one byte of data consists of the SPRL bit value, a don’t care bit,
four data bits to denote whether a Global Protect or Unprotect should be performed, and two additional don’t care bits
(see
SPRL bit in the Status Register will be modified, and the WEL bit in the Status Register will be reset back to a logical “0”.
The values of bits five, four, three and two and the state of the SPRL bit before the Write Status Register Byte 1 command
was executed (the prior state of the SPRL bit) will determine whether or not a Global Protect or Global Unprotect will be
performed. Please refer to
The complete one byte of data must be clocked into the device before the CS pin is deasserted, and the CS pin must be
deasserted on even byte boundaries (multiples of eight bits); otherwise, the device will abort the operation, the state of
the SPRL bit will not change, no potential Global Protect or Unprotect will be performed, and the WEL bit in the Status
Register will be reset back to the logical “0” state.
If the WP pin is asserted, then the SPRL bit can only be set to a logical “1”. If an attempt is made to reset the SPRL bit to
a logical “0” while the WP pin is asserted, then the Write Status Register Byte 1 command will be ignored, and the WEL
bit in the Status Register will be reset back to the logical “0” state. In order to reset the SPRL bit to a logical “0”, the WP
pin must be deasserted.
Table 11-3.
Figure 11-2. Write Status Register Byte 1
SCK
Atmel AT25DF321A
SO
CS
SPRL
Bit 7
SI
Table 11-3
). Any additional data bytes that are sent to the device will be ignored. When the CS pin is deasserted, the
Write Status Register Byte 1 Format
Bit 6
MSB
HIGH-IMPEDANCE
0
X
0
0
1
0
2
OPCODE
0
3
“Global Protect/Unprotect” on page 21
0
Bit 5
4
0
5
0
6
1
7
MSB
Global Protect/Unprotect
D
8
STATUS REGISTER IN
Bit 4
X
9
D
10 11
BYTE 1
D
D
12
D
13
Bit 3
X
14 15
X
for more details.
Bit 2
Bit 1
X
Bit 0
X
3686D–DFLASH–12/09