M25P64-VMF6TP NUMONYX, M25P64-VMF6TP Datasheet - Page 25
![IC FLASH 64MBIT 50MHZ 16SOIC](/photos/7/28/72855/m25p64-vmf6tp_sml.jpg)
M25P64-VMF6TP
Manufacturer Part Number
M25P64-VMF6TP
Description
IC FLASH 64MBIT 50MHZ 16SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P64-VME6TG.pdf
(55 pages)
Specifications of M25P64-VMF6TP
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
64M (8M x 8)
Speed
50MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P64-VMF6TP
M25P64-VMF6TPTR
M25P64-VMF6TPTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P64-VMF6TP
Manufacturer:
Numonyx
Quantity:
1 000
Company:
Part Number:
M25P64-VMF6TP
Manufacturer:
MICRONEOL84
Quantity:
1 016
Part Number:
M25P64-VMF6TP
Manufacturer:
STM
Quantity:
20 000
Company:
Part Number:
M25P64-VMF6TP-6JBS
Manufacturer:
OKI
Quantity:
270
Company:
Part Number:
M25P64-VMF6TP-N
Manufacturer:
STMicroelectronics
Quantity:
500
Company:
Part Number:
M25P64-VMF6TPBA
Manufacturer:
MICRON
Quantity:
1 001
6.3
Table 5.
Manufacturer identification
20h
Read Identification (RDID)
The read identification (RDID) instruction allows to read the device identification data:
The manufacturer identification is assigned by JEDEC, and has the value 20h for Numonyx.
The device identification is assigned by the device manufacturer, and indicates the memory
type in the first byte (20h), and the memory capacity of the device in the second byte (17h).
The UID contains the length of the following data in the first byte (set to 10h) and 16 bytes of
the optional customized factory data (CFD) content. The CFD bytes are read-only and can
be programmed with customers data upon their demand. If the customers do not make
requests, the devices are shipped with all the CFD bytes programmed to zero (00h).
Any read identification (RDID) instruction while an erase or program cycle is in progress, is
not decoded, and has no effect on the cycle that is in progress.
The read identification (RDID) instruction should not be issued while the device is in deep
power-down mode.
The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code
for the instruction is shifted in. After this, the 24-bit device identification, stored in the
memory, the 8-bit CFD length followed by 16 bytes of CFD content will be shifted out on
serial data output (DQ1). Each bit is shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in
The read identification (RDID) instruction is terminated by driving Chip Select (S) High at
any time during data output. When Chip Select (S) is driven High, the device is put in the
standby power mode. Once in the standby power mode, the device waits to be selected so
that it can receive, decode, and execute instructions.
Read identification (RDID) data-out sequence
1. The UID feature is available only for process technology T9HX devices, identified by process identification digit
"4" in the device marking.
Manufacturer identification (1 byte)
Device identification (2 bytes)
A unique ID code (UID) (17 bytes, of which 16 available upon customer request).
Memory type
20h
Device identification
Memory capacity
Figure
17h
10.
CFD length
10h
UID
CFD content
16 bytes
(1)
25/55