LPC1114FBD48/301,1 NXP Semiconductors, LPC1114FBD48/301,1 Datasheet - Page 55

• Manufacturer Part Number: LPC1114FBD48/301,1
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC1100r

Specifications of LPC1114FBD48/301,1

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM Cortex-M0
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 42
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC11
• Core: ARM Cortex M0
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Number Of Programmable I/os: 28
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC1114
• Development Tools By Supplier: OM11049, OM11085
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4950; 935290789151

NXP Semiconductors
11. Application information
LPC1111_12_13_14
Product data sheet
11.1 ADC usage notes
11.2 XTAL input
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
C
capacitor to ground C
mode, a minimum of 200 mV (RMS) is needed.
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in
Table 19
and the capacitances C
fundamental mode oscillation (the fundamental frequency is represented by L, C
R
not be larger than 7 pF. Parameters F
manufacturer (see
Fig 30. Slave mode operation of the on-chip oscillator
•
•
•
•
i
S
= 100 pF. To limit the input voltage to the specified range, choose an additional
). Capacitance C
The ADC input trace must be short and as close as possible to the LPC1111/12/13/14
chip.
The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
30), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
and
Table
All information provided in this document is subject to legal disclaimers.
Table
P
20. Since the feedback resistance is integrated on chip, only a crystal
in
g
Rev. 4 — 10 February 2011
which attenuates the input voltage by a factor C
Figure 31
X1
19).
and C
X2
represents the parallel package capacitance and should
need to be connected externally in case of
OSC
XTALIN
LPC1xxx
C i
100 pF
, C
L
, R
S
002aae788
32-bit ARM Cortex-M0 microcontroller
C g
and C
LPC1111/12/13/14
Table
P
are supplied by the crystal
8:
i
/(C
© NXP B.V. 2011. All rights reserved.
Figure 31
i
+ C
g
). In slave
L
and
and in
55 of 66