C8051F353-GM Silicon Laboratories Inc, C8051F353-GM Datasheet - Page 161

• Manufacturer Part Number: C8051F353-GM
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F353-GM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F350DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 16-bit
• On-chip Dac: 2-ch x 8-bit
• No. Of I/o's: 17
• Ram Memory Size: 768Byte
• Cpu Speed: 50MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Package: 28QFN
• Device Core: 8051
• Family Name: C8051F35x
• Maximum Speed: 50 MHz
• Data Rom Size: 128 B
• Height: 0.88 mm
• Length: 5 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1083 - DEV KIT FOR F350/351/352/353
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1273

ARBLOST
MASTER
TXMODE
ACKRQ
STO
ACK
STA
Bit
SI
• A START is generated.
• START is generated.
• SMB0DAT is written before the start of an
• A START followed by an address byte is
• A STOP is detected while addressed as a
• Arbitration is lost due to a detected STOP.
• A byte has been received and an ACK
• A repeated START is detected as a MASTER
• SCL is sensed low while attempting to gener-
• SDA is sensed low while transmitting a ‘1’
• The incoming ACK value is low (ACKNOWL-
• A START has been generated.
• Lost arbitration.
• A byte has been transmitted and an
• A byte has been received.
• A START or repeated START followed by a
• A STOP has been received.
Table 19.3. Sources for Hardware Changes to SMB0CN
SMBus frame.
received.
slave.
response value is needed.
when STA is low (unwanted repeated START).
ate a STOP or repeated START condition.
(excluding ACK bits).
EDGE).
ACK/NACK received.
slave address + R/W has been received.
Set by Hardware When:
Rev. 1.1
• A STOP is generated.
• Arbitration is lost.
• A START is detected.
• Arbitration is lost.
• SMB0DAT is not written before the
• Must be cleared by software.
• A pending STOP is generated.
• After each ACK cycle.
• Each time SI is cleared.
• The incoming ACK value is high (NOT
• Must be cleared by software.
start of an SMBus frame.
ACKNOWLEDGE).
Cleared by Hardware When:
C8051F350/1/2/3
161