ATTINY461V-10SU Atmel, ATTINY461V-10SU Datasheet - Page 181

• Manufacturer Part Number: ATTINY461V-10SU
• Description: IC MCU AVR 4K FLASH 10MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY461V-10SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire, SPI, USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 20SOIC W
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 10 MHz
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2588E–AVR–08/10
While the lower bits in the address are mapped to words within the page, the higher bits address
the pages within the FLASH. This is illustrated in
required to address words in the page (pagesize < 256), the most significant bit(s) in the address
low byte are used to address the page when performing a Page Write.
3. Load Data Low Byte:
4. Load Data High Byte:
5. Repeat steps 2 to 4 until the entire buffer is filled or until all data within the page is
6. Load Address High byte:
7. Program Page:
8. Repeat steps 2 to 7 until the entire Flash is programmed or until all data has been
9. End Page Programming:
a. Set XA1, XA0 to “01”. This enables data loading.
b. Set DATA = Data low byte (0x00 - 0xFF).
c. Give XTAL1 a positive pulse. This loads the data byte.
a. Set BS1 to “1”. This selects high data byte.
b. Keep XA1, XA0 at “01”. This enables data loading.
c. Set DATA = Data high byte (0x00 - 0xFF).
d. Give XTAL1 a positive pulse. This loads the data byte.
loaded.
a. Set XA1, XA0 to “00”. This enables address loading.
b. Set BS1 to “1”. This selects high address.
c. Set DATA = Address high byte (0x00 - 0xFF).
d. Give XTAL1 a positive pulse. This loads the address high byte.
a. Give WR a negative pulse. This starts programming of the entire page of data.
b. Wait until RDY/BSY goes high.
programmed.
a. Set XA1, XA0 to “10”. This enables command loading.
b. Set DATA to “0000 0000”. This is the command for No Operation.
c. Give XTAL1 a positive pulse. This loads the command, and the internal write sig-
RDY/BSY goes low.
nals are reset.
Figure
18-4. Note that if less than eight bits are
181