MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 112

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Low-Power Modes
10.3 Break Module (BRK)
10.3.1 Wait Mode
If enabled, the break (BRK) module is active in wait mode. In the break routine, the user can subtract one
from the return address on the stack if the SBSW bit in the break status register is set.
10.3.2 Stop Mode
The break module is inactive in stop mode. A break interrupt causes exit from stop mode and sets the
SBSW bit in the break status register. The STOP instruction does not affect break module register states.
10.4 Central Processor Unit (CPU)
10.4.1 Wait Mode
The WAIT instruction:
10.4.2 Stop Mode
The STOP instruction:
After exiting stop mode, the CPU clock begins running after the oscillator stabilization delay.
10.5 Clock Generator Module (CGM)
10.5.1 Wait Mode
The clock generator module (CGM) remains active in wait mode. Before entering wait mode, software can
disengage and turn off the PLL by clearing the BCS and PLLON bits in the PLL control register (PCTL).
Less power-sensitive applications can disengage the PLL without turning it off. Applications that require
the PLL to wake the MCU from wait mode also can deselect the PLL output without turning off the PLL.
10.5.2 Stop Mode
If the OSCSTOPEN bit in the CONFIG register is cleared (default), then the STOP instruction disables
the CGM (oscillator and phase-locked loop) and holds low all CGM outputs (CGMXCLK, CGMOUT, and
CGMINT).
If the OSCSTOPEN bit in the CONFIG register is set, then the phase locked loop is shut off, but the
oscillator will continue to operate in stop mode.
112
•
•
•
•
Clears the interrupt mask (I bit) in the condition code register, enabling interrupts. After exit from
wait mode by interrupt, the I bit remains clear. After exit by reset, the I bit is set.
Disables the CPU clock
Clears the interrupt mask (I bit) in the condition code register, enabling external interrupts. After
exit from stop mode by external interrupt, the I bit remains clear. After exit by reset, the I bit is set.
Disables the CPU clock
MC68HC908GR16 Data Sheet, Rev. 5.0
Freescale Semiconductor