MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 191

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.6.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are disabled. An interrupt request from a
module can cause an exit from stop mode. Stacking for interrupts begins after the selected stop recovery
time has elapsed. Reset also causes an exit from stop mode.
The SIM disables the clock generator module outputs (CGMOUT and CGMXCLK) in stop mode, stopping
the CPU and peripherals. Stop recovery time is selectable using the SSREC bit in the mask option register
(MOR). If SSREC is set, stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles down
to 32. This is ideal for applications using canned oscillators that do not require long startup times from
stop mode.
The SIM counter is held in reset from the execution of the STOP instruction until the beginning of stop
recovery. It is then used to time the recovery period.
15-20
Freescale Semiconductor
shows stop mode recovery time from interrupt.
External crystal applications should use the full stop recovery time by
clearing the SSREC bit.
To minimize stop current, all pins configured as inputs should be driven to
a 1 or 0.
CGMXCLK
Note: Previous data can be operand data or the STOP opcode, depending
CPUSTOP
RST
IDB
IAB
R/W
IDB
IAB
on the last instruction.
$A6
Figure 15-18. Wait Recovery from Internal Reset
STOP ADDR
$6E0B
$A6
Figure 15-19. Stop Mode Entry Timing
PREVIOUS DATA
MC68HC908GR16 Data Sheet, Rev. 5.0
$A6
STOP ADDR + 1
CYCLES
32
NOTE
NOTE
NEXT OPCODE
Figure 15-19
CYCLES
32
SAME
shows stop mode entry timing.
RST VCT H
SAME
RST VCT L
SAME
SAME
Low-Power Modes
Figure
191