MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 63

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

The PLL also may operate in manual mode (AUTO = 0). Manual mode is used by systems that do not
require an indicator of the lock condition for proper operation. Such systems typically operate well below
f
The following conditions apply when in manual mode:
4.3.6 Programming the PLL
The following procedure shows how to program the PLL.
Freescale Semiconductor
BUSMAX
1. Choose the desired bus frequency, f
2. Calculate the desired VCO frequency (four times the desired bus frequency).
3. Choose a practical PLL (crystal) reference frequency, f
•
•
•
•
•
•
•
The LOCK bit is set when the VCO frequency is within a certain tolerance and is cleared when the
VCO frequency is out of a certain tolerance. (See
more information.)
CPU interrupts can occur if enabled (PLLIE = 1) when the PLL’s lock condition changes, toggling
the LOCK bit. (See
ACQ is a writable control bit that controls the mode of the filter. Before turning on the PLL in manual
mode, the ACQ bit must be clear.
Before entering tracking mode (ACQ = 1), software must wait a given time, t
Acquisition/Lock Time
register (PCTL).
Software must wait a given time, t
clock source to CGMOUT (BCS = 1).
The LOCK bit is disabled.
CPU interrupts from the CGM are disabled.
Typically, the reference crystal is 32.768 kHz and R = 1.
Frequency errors to the PLL are corrected at a rate of f
this rate must be as fast as possible. The VCO frequency must be an integer multiple of this rate.
The relationship between the VCO frequency, f
P, the power of two multiplier, and N, the range multiplier, are integers.
In cases where desired bus frequency has some tolerance, choose f
either by other module requirements (such as modules which are clocked by CGMXCLK), cost
requirements, or ideally, as high as the specified range allows. See
Specifications. Choose the reference divider, R = 1. After choosing N and P, the actual bus
frequency can be determined using equation in 2 above.
.
The round function in the following equations means that the real number
should be rounded to the nearest integer number.
4.5.1 PLL Control
Specifications), after turning on the PLL by setting PLLON in the PLL control
MC68HC908GR16 Data Sheet, Rev. 5.0
f
AL
VCLKDES
f
, after entering tracking mode before selecting the PLL as the
VCLK
BUSDES
Register.)
=
NOTE
=
.
2
----------- f
P
R
4
N
×
VCLK
(
f
BUSDES
RCLK
4.8 Acquisition/Lock Time Specifications
, and the reference frequency, f
RCLK
)
RCLK
/R. For stability and lock time reduction,
, and the reference clock divider, R.
Chapter 20 Electrical
RCLK
to a value determined
ACQ
Functional Description
(see
RCLK
4.8
, is
for
63