ATMEGA163-8AI Atmel, ATMEGA163-8AI Datasheet - Page 46

• Manufacturer Part Number: ATMEGA163-8AI
• Description: IC AVR MCU 16K A/D 8MHZ 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA163-8AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Timer/Counter1 – TCNT1H
and TCNT1L
46
ATmega163(L)
When the prescaler is set to divide by eight, the Timer will count like this:
... | C-1, C-1, C-1, C-1, C-1, C-1, C-1, C-1 | C, C, C, C, C, C, C, C | 0, 0, 0, 0, 0, 0, 0, 0
|1,1,1,1,1,1,1,1|...
In PWM mode, this bit has a different function. If the CTC1 bit is cleared in PWM mode,
the Timer/Counter1 acts as an up/down counter. If the CTC1 bit is set (one), the
Timer/Counter wraps when it reaches the TOP value. Refer to page 48 for a detailed
description.
• Bits 2..0 – CS12, CS11, CS10: Clock Select1, Bit 2, 1, and 0
The Clock Select1 bits 2, 1, and 0 define the prescaling source of Timer/Counter1.
Table 14. Clock 1 Prescale Select
The Stop condition provides a Timer Enable/Disable function. The prescaled modes are
scaled directly from the CK Oscillator clock. If the external pin modes are used for
Timer/Counter1, transitions on PB1/(T1) will clock the counter even if the pin is config-
ured as an output. This feature can give the user SW control of the counting.
This 16-bit register contains the prescaled value of the 16-bit Timer/Counter1. To
ensure that both the high and low bytes are read and written simultaneously when the
CPU accesses these registers, the access is performed using an 8-bit temporary regis-
ter (TEMP). This temporary register is also used when accessing OCR1A, OCR1B, and
ICR1. If the main program and also interrupt routines perform access to registers using
TEMP, interrupts must be disabled during access from the main program and interrupt
routines.
Bit
$2D ($4D)
$2C ($4C)
Read/Write
Initial Value
CS12
0
0
0
0
1
1
1
1
MSB
R/W
R/W
CS11
15
7
0
0
0
0
1
1
0
0
1
1
R/W
R/W
14
6
0
0
CS10
0
1
0
1
0
1
0
1
R/W
R/W
13
5
0
0
Description
Stop, the Timer/Counter1 is stopped.
CK
CK/8
CK/64
CK/256
CK/1024
External Pin T1, falling edge
External Pin T1, rising edge
R/W
R/W
12
4
0
0
R/W
R/W
11
3
0
0
R/W
R/W
10
2
0
0
R/W
R/W
9
1
0
0
LSB
R/W
R/W
8
0
0
0
1142E–AVR–02/03
TCNT1H
TCNT1L