IS-C1603 NKK Switches, IS-C1603 Datasheet - Page 41

• Manufacturer Part Number: IS-C1603
• Description: CONTROL FOR 36X24 LCD PB/DISPLAY
• Manufacturer: NKK Switches

Specifications of IS-C1603

• Accessory Type: Controller
• Description/function: SMARTSWITCH Development Kit
• For Use With/related Products: SmartSwitch™ Switches
• For Use With: IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 360-2427

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Page
7. Programming the Firmware
The controller firmware can be programmed via the RS232 connection.
The Dallas semiconductor MTK software can be downloaded from the site below.
http://www.maxim-ic.com/products/microcontrollers/software/index.cfm#development
After you install the MTK software follow the following instructions to program the microcontroller:
1. Disconnect the switches from the controller at JP2.
2. Install a jumper on JPR connector (top right side of the board). This will put the microcontroller into
3. Run MTK software.
4. Select device DS89C450.
5. Under menu item “Options” select the “Configure Serial Port” and select relevant port and 19200 baud rate.
6. Under menu item “Target” select “Open COM X at 19200 baud”.
7. Plug in or power up the IS-C1603 controller.
8. Under menu item “Target” select “Connect to Loader”.
9. The microcontroller will respond with a version number and copyright notice in blue.
10. Under menu item “File” select “Load Flash”.
11. Specify the HEX file provided by NKK Switches (e.g. C1603V13.HEX)
12. Once loaded the display shall say “Load Complete”
Note: The switches should not be connected while programming the controller since they are not being
refreshed during programming.
8. Firmware Issues
The problems found in the most current version are listed below and will be resolved in the following version.
Version 1.3
IS-C1603 Intelligent Controller Users Manual C.doc
programming mode.
1.
No firmware issues at this time.
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
IS-C1603 Intelligent Controller Users
The data at each address. Each Page has image data, LCD/LED data, attribute
block data, and user-define picture closure/release data.
www.nkkswitches.com • Email [e-mail]
Manual
Page 41 of 45
0110