AT90PWM161 Atmel Corporation, AT90PWM161 Datasheet - Page 154

• Manufacturer Part Number: AT90PWM161
• Manufacturer: Atmel Corporation

Specifications of AT90PWM161

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 20
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 8
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

13.5.3
13.6
154
Update of Values
AT90PWM81
Fifty Percent Waveform Configuration
Figure 13-6.
On-Time 0 = (OCRrRAH/L - OCRrSAH/L) * 1/Fclkpsc
On-Time 1 = (OCRrRBH/L - OCRrSBH/L) * 1/Fclkpsc
Dead-Time 0 = (OCRrSAH/L + 1) * 1/Fclkpsc
Dead-Time 1 = (OCRrSBH/L - OCRrRAH/L) * 1/Fclkpsc
Note:
When PSCOUTr0 and PSCOUTr1 have the same characteristics, it’s possible to configure the PSCR in a
Fifty Percent mode. When the PSCR is in this configuration, it duplicates the OCRrSBH/L and OCR-
rRBH/L registers in OCRrSAH/L and OCRrRAH/L registers. So it is not necessary to program
OCRrSAH/L and OCRrRAH/L registers.
The update of PSCR waveform registers are done in the following way:
•
•
•
To avoid asynchronous and incoherent values in a cycle, if an update of one of several values is necessary,
all values are updated at the same time at the end of the cycle by the PSC. The new set of values is calcu-
lated by software and the update is initiated by software.
PSC Counter
PSCOUTn0
PSCOUTn1
Immediately when the PSC is stopped
At the PSC end of cycle when the PSC is running
At the PSC end of cycle following the required condition when LOCK or AUTOLOCK modes are
used.
Minimal value for Dead-Time 0 = 1/Fclkpsc
OCRnSA
0
PSCr0 & PSCr1 Basic Waveforms in One Ramp mode
Dead-Time 0
On-Time 0
PSC Cycle
OCRnRA
OCRnSB
Dead-Time 1
On-Time 1
OCRnRB
7734P–AVR–08/10