AT90PWM161 Atmel Corporation, AT90PWM161 Datasheet - Page 98

• Manufacturer Part Number: AT90PWM161
• Manufacturer: Atmel Corporation

Specifications of AT90PWM161

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 20
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 8
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

11.8.5
98
AT90PWM81
Timer/Counter1 Interrupt Flag Register – TIFR1
• Bit 7, 6 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 5 – ICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally enabled), the
Timer/Counter1 Input Capture interrupt is enabled. The corresponding Interrupt Vector (see XXXX) is
executed when the ICF1 Flag, located in TIFR1, is set.
• Bit 4, 3, 2,1 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 0 – TOIE1: Timer/Counter1, Overflow Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally enabled), the
Timer/Counter1 Overflow interrupt is enabled. The corresponding Interrupt Vector (see
61) is executed when the TOV1 Flag, located in TIFR1, is set.
• Bit 7, 6 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 5 – ICF1: Timer/Counter1, Input Capture Flag
This flag is set when a capture event occurs on the ICP1 pin. When the Input Capture Register (ICR1) is
set by the WGM13:0 to be used as the TOP value, the ICF1 Flag is set when the counter reaches the TOP
value.
ICF1 is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively, ICF1
can be cleared by writing a logic one to its bit location.
• Bit 4, 3, 2,1 – Res: Reserved Bits
• Bit 0 – TOV1: Timer/Counter1, Overflow Flag
The setting of this flag is dependent of the WG.
TOV1 is automatically cleared when the Timer/Counter1 Overflow Interrupt Vector is executed. Alterna-
tively, TOV1 can be cleared by writing a logic one to its bit location.
Bit
Read/Write
Initial Value
7
–
R
0
R
6
–
0
5
ICF1
R/W
0
4
–
R
0
3
–
R
0
2
–
R/W
0
1
–
R/W
0
0
TOV1
R/W
0
Table 8-1 on page
7734P–AVR–08/10
TIFR1