ATmega64M1 Atmel Corporation, ATmega64M1 Datasheet - Page 48

• Manufacturer Part Number: ATmega64M1
• Manufacturer: Atmel Corporation

Specifications of ATmega64M1

• Flash (kbytes): 64 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

48
ATmega16M1/32M1/64M1
Note:
Note: If the Watchdog is accidentally enabled, for example by a runaway pointer or brown-out
condition, the device will be reset and the Watchdog Timer will stay enabled. If the code is not
set up to handle the Watchdog, this might lead to an eternal loop of time-out resets. To avoid this
situation, the application software should always clear the Watchdog System Reset Flag
(WDRF) and the WDE control bit in the initialisation routine, even if the Watchdog is not in use.
The following code example shows one assembly and one C function for changing the time-out
value of the Watchdog Timer.
Assembly Code Example
C Code Example
WDT_off:
void WDT_off(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Clear WDRF in MCUSR
in
andi
out
; Write logical one to WDCE and WDE
; Keep old prescaler setting to prevent unintentional time-out
lds r16, WDTCSR
ori
sts WDTCSR, r16
; Turn off WDT
ldi
sts WDTCSR, r16
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Clear WDRF in MCUSR */
MCUSR &= ~(1<<WDRF);
/* Write logical one to WDCE and WDE */
/* Keep old prescaler setting to prevent unintentional time-out */
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Turn off WDT */
WDTCSR = 0x00;
__enable_interrupt();
1. The example code assumes that the part specific header file is included
r16, MCUSR
r16, (0xff & (0<<WDRF))
MCUSR, r16
r16, (1<<WDCE) | (1<<WDE)
r16, (0<<WDE)
(1)
(1)
8209D–AVR–11/10