TMPM364F10FG Toshiba, TMPM364F10FG Datasheet - Page 79

• Manufacturer Part Number: TMPM364F10FG
• Manufacturer: Toshiba

Specifications of TMPM364F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 144
• Package: LQFP(20x20)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 5
• Uart/sio (ch): 12
• Usb: Host
• Can: 1
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 16
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

6.6
6.6.1
to the low power consumption mode, specify the mode in the system control register CGSTBYCR<STBY[2:0]>
and execute the WFI (Wait For Interrupt) instruction.In this case, execute reset or generate the interrupt to release
the mode. Releasing by the interrupt requires settings in advance. See the chapter "Exceptions" for details.
6.6.1.1
6.6.1.2
Note 1: The TMPM364F10FG does not offer any event for releasing the low power consumption mode. Transition to
Note 2: The TMPM364F10FG does not support the low power consumption mode configured with the SLEEPDEEP
Low Power Consumption Modes
The TMPM364F10FG has three low power consumption modes: IDLE1, IDLE2, SLEEP and STOP. To shift
The features of each mode are described as follows.
abling or disabling operation in the IDLE mode. When the IDLE mode is enabled, peripheral functions for
which operation in the IDLE mode is disabled stop operation and hold the state at that time.
the chapter on each peripheral function.
IDLE Mode (IDLE2, IDLE1)
Only the CPU, SSP is stopped in this mode. Each peripheral function has one bit in its control register for en-
The following peripheral functions can be enabled or disabled in the IDLE mode. For setting details, see
range and the peripherals performance are equivalent for the normal mode besides power consumption is re-
duced compared to the normal mode.
ing the IDLE1 mode, the conditions are refer to Table 6-7 and Operation frequency must be set as fol-
lows; fsys=1MHz (fosc=8MHz, PLL multiplier circuit stop, clock gear 1/8).
the low power consumption mode by executing the WFE (Wait For Event) instruction is prohibited.
bit in the Cortex-M3 core. Setting the <SLEEPDEEP> bit of the system control register is prohibited.
・ 16-bit timer / event counter (TMRB)
・ Serial channel (SIO/UART)
・ Serial bus interface (I2C/SIO)
・ AD converter (ADC)
・ Watchdog timer (WDT)
In the IDLE2 mode, CPU and SSP stop and other peripherals can be operated. Operation frequency
The IDLE1 mode is decreased power supply ability than IDEL2 to realize low power consumption. Us-
IDLE2 mode
IDLE1 mode
Page 53
TMPM364F10FG