PIC18F1320-I/SS Microchip Technology, PIC18F1320-I/SS Datasheet - Page 149

IC MCU FLASH 4KX16 A/D 20SSOP

PIC18F1320-I/SS

Manufacturer Part Number
PIC18F1320-I/SS
Description
IC MCU FLASH 4KX16 A/D 20SSOP
Manufacturer
Microchip Technology
Series
PIC® 18Fr

Specifications of PIC18F1320-I/SS

Core Size
8-Bit
Program Memory Size
8KB (4K x 16)
Core Processor
PIC
Speed
40MHz
Connectivity
UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
16
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 7x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-SSOP
Controller Family/series
PIC18
No. Of I/o's
16
Eeprom Memory Size
256Byte
Ram Memory Size
256Byte
Cpu Speed
40MHz
No. Of Timers
4
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
EUSART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
16
Number Of Timers
1 x 16 bit
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
7 bit
Package
20SSOP
Device Core
PIC
Family Name
PIC18
Maximum Speed
40 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC164307 - MODULE SKT FOR PM3 28SSOPAC164018 - MODULE SKT PROMATEII 20SSOP
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F1320-I/SS
Manufacturer:
MICROCHIP
Quantity:
8 000
Part Number:
PIC18F1320-I/SS
Manufacturer:
MIC
Quantity:
20 000
16.3.6.2
To receive a Break Sync:
1.
2.
3.
4.
5.
6.
FIGURE 16-9:
© 2007 Microchip Technology Inc.
Write to TXREG
Configure the EUSART for asynchronous
transmit and receive. TXEN should remain
clear. SPBRGH:SPBRG may be left as is.
Enable auto-wake-up. Set WUE.
Enable RXIF interrupts. Set RCIE, PEIE, GIE.
The controller may be placed in any power
managed mode.
An RCIF will be generated at the beginning of
the Break signal. When the interrupt is received,
read RCREG to clear RCIF and discard. Allow
the controller to return to PRI_RUN mode.
Wait for the RX line to go high at the end of the
Break signal. Wait for any of the following: WUE
to clear automatically (poll), RB4/RX to go high
(poll) or for RBIF to be set (poll or interrupt). If
RBIF is used, check to be sure that RB4/RX is
high before continuing.
BRG Output
(Shift Clock)
TRMT bit
TX (pin)
TXIF bit
SENDB
Receiving a Break Sync
SEND BREAK CHARACTER SEQUENCE
Dummy Write
Start Bit
Bit 0
Bit 1
Break
7.
8.
9.
10. Process subsequent RCIF interrupts normally
Enable Auto-Baud Rate Detect. Set ABDEN.
Return from the interrupt. Allow the primary
clock to start and stabilize (PRI_RUN or
PRI_IDLE).
When the next RCIF interrupt occurs, the
received baud rate has been measured. Read
RCREG to clear RCIF and discard. Check
SPBRGH:SPBRG for a valid value. The
EUSART is ready for normal communications.
Return from the interrupt. Allow the primary
clock to run (PRI_RUN or PRI_IDLE).
as in asynchronous reception. TXEN should
now be set if transmissions are needed. TXIF
and TXIE may be set if transmit interrupts are
desired. Remain in PRI_RUN or PRI_IDLE until
communications are complete. Clear TXEN and
return to step 2.
PIC18F1220/1320
Bit 11
Stop Bit
DS39605F-page 147

Related parts for PIC18F1320-I/SS