PIC18F6310-I/PT Microchip Technology, PIC18F6310-I/PT Datasheet - Page 220

• Manufacturer Part Number: PIC18F6310-I/PT
• Description: IC PIC MCU FLASH 4KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6310-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/EUSART/AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
17.2
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTA1<4>). In this mode, the
EUSART uses standard Non-Return-to-Zero (NRZ) for-
mat (one Start bit, eight or nine data bits and one Stop bit).
The most common data format is 8 bits. An on-chip dedi-
cated 8-bit/16-bit Baud Rate Generator can be used to
derive standard baud rate frequencies from the oscillator.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent, but use the same data format and baud
rate. The Baud Rate Generator produces a clock, either
x16 or x64 of the bit shift rate depending on the BRGH
and BRG16 bits (TXSTA1<2> and BAUDCON1<3>).
Parity is not supported by the hardware but can be
implemented in software and stored as the 9th data bit.
When operating in Asynchronous mode, the EUSART
module consists of the following important elements:
• Baud Rate Generator
• Sampling Circuit
• Asynchronous Transmitter
• Asynchronous Receiver
• Auto-Wake-up on Sync Break Character
• 12-bit Break Character Transmit
• Auto-Baud Rate Detection
17.2.1
The EUSART transmitter block diagram is shown in
Figure 17-3. The heart of the transmitter is the Transmit
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG1. The TXREG1 register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREG1 register (if available).
FIGURE 17-3:
DS39635A-page 218
EUSART Asynchronous Mode
BRG16
EUSART ASYNCHRONOUS
TRANSMITTER
TX1IE
Interrupt
EUSART TRANSMIT BLOCK DIAGRAM
SPBRGH1
Baud Rate Generator
TX1IF
TXEN
Baud Rate CLK
SPBRG1
MSb
(8)
TXREG1 Register
Preliminary
TSR Register
TX9D
• • •
TX9
8
Data Bus
Once the TXREG1 register transfers the data to the
TSR register (occurs in one T
is empty and the TX1IF flag bit (PIR1<4>) is set. This
interrupt can be enabled or disabled by setting or clear-
ing the interrupt enable bit, TX1IE (PIE1<4>). TX1IF
will be set regardless of the state of TX1IE; it cannot be
cleared in software. TX1IF is also not cleared immedi-
ately upon loading TXREG1, but becomes valid in the
second instruction cycle following the load instruction.
Polling TX1IF immediately following a load of TXREG1
will return invalid results.
While TX1IF indicates the status of the TXREG1 regis-
ter, another bit, TRMT (TXSTA1<1>), shows the status
of the TSR register. TRMT is a read-only bit which is set
when the TSR register is empty. No interrupt logic is
tied to this bit so the user has to poll this bit in order to
determine if the TSR register is empty.
To set up an Asynchronous Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Note 1: The TSR register is not mapped in data
Initialize the SPBRGH1:SPBRG1 registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit TX1IE.
If 9-bit transmission is desired, set transmit bit
TX9; can be used as address/data bit.
Enable the transmission by setting bit TXEN,
which will also set bit TX1IF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG1 register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
LSb
2: Flag bit TX1IF is set when enable bit
0
memory so it is not available to the user.
TXEN is set.
TRMT
and Control
Pin Buffer
 2004 Microchip Technology Inc.
SPEN
CY
), the TXREG1 register
TX1 pin