AT91SAM7S32B-AU Atmel, AT91SAM7S32B-AU Datasheet - Page 523

• Manufacturer Part Number: AT91SAM7S32B-AU
• Description: IC MCU ARM7 32KB FLASH 48LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S32B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: I²C, SPI, SSC, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Interface Type: SPI/TWI/USART
• Total Internal Ram Size: 8KB
• # I/os (max): 21
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: AT91
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

35.6.7
Register Name:
Access Type:
• EP0INT: Endpoint 0 Interrupt Status
• EP1INT: Endpoint 1 Interrupt Status
• EP2INT: Endpoint 2 Interrupt Status
• EP3INT: Endpoint 3 Interrupt Status
0 = No Endpoint0 Interrupt pending.
1 = Endpoint0 Interrupt has been raised.
Several signals can generate this interrupt. The reason can be found by reading UDP_ CSR0:
EP0INT is a sticky bit. Interrupt remains valid until EP0INT is cleared by writing in the corresponding UDP_ CSR0 bit.
• RXSUSP: UDP Suspend Interrupt Status
0 = No UDP Suspend Interrupt pending.
1 = UDP Suspend Interrupt has been raised.
The USB device sets this bit when it detects no activity for 3ms. The USB device enters Suspend mode.
• RXRSM: UDP Resume Interrupt Status
0 = No UDP Resume Interrupt pending.
1 =UDP Resume Interrupt has been raised.
The USB device sets this bit when a UDP resume signal is detected at its port.
After reset, the state of this bit is undefined, the application must clear this bit by setting the RXRSM flag in the UDP_ ICR
register.
6175K–ATARM–30-Aug-10
RXSETUP set to 1
RX_DATA_BK0 set to 1
RX_DATA_BK1 set to 1
TXCOMP set to 1
STALLSENT set to 1
31
23
15
–
–
–
7
UDP Interrupt Status Register
30
22
14
UDP_ ISR
Read-only
–
–
–
6
WAKEUP
29
21
13
–
–
5
ENDBUSRES
28
20
12
–
–
4
AT91SAM7S Series Preliminary
SOFINT
EP3INT
27
19
11
–
–
3
EP2INT
26
18
10
–
–
–
2
RXRSM
EP1INT
25
17
–
–
9
1
RXSUSP
EP0INT
24
16
–
–
8
0
523