AT91M40800-33AU Atmel, AT91M40800-33AU Datasheet - Page 105

• Manufacturer Part Number: AT91M40800-33AU
• Description: IC ARM7 MCU 100 LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M40800-33AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100TQFP
• Device Core: ARM7TDMI
• Family Name: 91M
• Maximum Speed: 33 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 32
• Interface Type: EBI/USART
• Number Of Timers: 3
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Ram Size: 8 KB
• Maximum Clock Frequency: 33 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• Eeprom Memory: 0 Bytes
• Input Output: 32
• Interface: EBI/EMI, UART/USART
• Ios: 32
• Memory Type: ROMless
• Number Of Bits: 32
• Package Type: 100-pin LQFP
• Programmable Memory: 0 Bytes
• Timers: 3-16-bit
• Voltage, Range: 1.8-3.6 V
• Cpu Family: 91M
• Device Core Size: 32b
• Frequency (max): 33MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 8KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Receive Break
Peripheral Data
Controller
Interrupt Generation
Channel Modes
1354D–ATARM–08/02
Each of these steps can be scheduled by using the interrupt if the bit TXRDY in US_IMR
is set. For character transmission, the USART channel must be enabled before sending
a break.
The receiver detects a break condition when all data, parity and stop bits are low. When
the low stop bit is detected, the receiver asserts the RXBRK bit in US_CSR. An end of
receive break is detected by a high level for at least 2/16 of a bit period in Asynchronous
Mode or at least one sample in Synchronous Mode. RXBRK is also asserted when an
end of break is detected.
Both the beginning and the end of a break can be detected by interrupt if the bit
US_IMR.RXBRK is set.
Each USART channel is closely connected to a corresponding Peripheral Data Control-
ler channel. One is dedicated to the receiver. The other is dedicated to the transmitter.
Note:
The PDC channel is programmed using US_TPR (Transmit Pointer) and US_TCR
(Transmit Counter) for the transmitter and US_RPR (Receive Pointer) and US_RCR
(Receive Counter) for the receiver. The status of the PDC is given in US_CSR by the
ENDTX bit for the transmitter and by the ENDRX bit for the receiver.
The pointer registers (US_TPR and US_RPR) are used to store the address of the
transmit or receive buffers. The counter registers (US_TCR and US_RCR) are used to
store the size of these buffers.
The receiver data transfer is triggered by the RXRDY bit and the transmitter data trans-
fer is triggered by TXRDY. When a transfer is performed, the counter is decremented
and the pointer is incremented. When the counter reaches 0, the status bit is set
(ENDRX for the receiver, ENDTX for the transmitter in US_CSR) which can be pro-
grammed to generate an interrupt. Transfers are then disabled until a new non-zero
counter value is programmed.
Each status bit in US_CSR has a corresponding bit in US_IER (Interrupt Enable) and
US_IDR (Interrupt Disable) which controls the generation of interrupts by asserting the
USART interrupt line connected to the Advanced Interrupt Controller. US_IMR (Interrupt
Mask Register) indicates the status of the corresponding bits.
When a bit is set in US_CSR and the same bit is set in US_IMR, the interrupt line is
asserted.
The USART can be programmed to operate in three different test modes, using the field
CHMODE in US_MR.
Automatic Echo Mode allows bit by bit re-transmission. When a bit is received on the
RXD line, it is sent to the TXD line. Programming the transmitter has no effect.
Local Loopback Mode allows the transmitted characters to be received. TXD and RXD
pins are not used and the output of the transmitter is internally connected to the input of
the receiver. The RXD pin level has no effect and the TXD pin is held high, as in idle
state.
Remote Loopback Mode directly connects the RXD pin to the TXD pin. The Transmitter
and the Receiver are disabled and have no effect. This mode allows bit by bit re-
transmission.
The PDC is disabled if 9-bit character length is selected (MODE9 = 1) in US_MR.
AT91X40 Series
105