ATMEGA1280V-8AU Atmel, ATMEGA1280V-8AU Datasheet - Page 350

• Manufacturer Part Number: ATMEGA1280V-8AU
• Description: IC MCU AVR 128K FLASH 100-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA1280V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Package: 100TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Controller Family/series: AVR MEGA
• No. Of I/o's: 86
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

29.8.1
29.8.2
2549M–AVR–09/10
Serial Programming Pin Mapping
Serial Programming Algorithm
Table 29-15. Pin Mapping Serial Programming
Figure 29-10. Serial Programming and Verify
Notes:
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
When writing serial data to the ATmega640/1280/1281/2560/2561, data is clocked on the rising
edge of SCK.
When reading data from the ATmega640/1280/1281/2560/2561, data is clocked on the falling
edge of SCK. See
Symbol
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
PDO
SCK
PDI
XTAL1 pin.
programming the EEPROM, an auto-erase cycle is built into the self-timed programming oper-
ation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
CC
- 0.3V < AVCC < V
Figure 29-12 on page 353
(TQFP-100)
Pins
PB2
PB3
PB1
PDO
SCK
PDI
ck
ck
CC
ATmega640/1280/1281/2560/2561
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
+ 0.3V, however, AVCC should always be within 1.8V - 5.5V.When
XT AL1
RESET
GND
(TQFP-64)
for timing details.
(1)
Pins
PE0
PE1
PB1
AVCC
VCC
+1.8V - 5.5V
+1.8V - 5.5V
I/O
O
I
I
(2)
ck
ck
>= 12 MHz
>= 12 MHz
Serial Data out
Serial Data in
Description
Serial Clock
350