MC908JB16DWE Freescale Semiconductor, MC908JB16DWE Datasheet - Page 119

• Manufacturer Part Number: MC908JB16DWE
• Description: IC MCU 16K FLASH 6MHZ USB 28SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16DWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.8.2 SIM Reset Status Register (SRSR)
MC68HC908JB16
Freescale Semiconductor
;
;
;
;
This code works if the H register has been pushed onto the stack in the break
service routine software. This code should be executed at the end of the break
service routine software.
HIBYTE
LOBYTE
DOLO
RETURN
EQU
EQU
If not SBSW, do RTI
BRCLR
TST
BNE
DEC
DEC
PULH
RTI
—
Rev. 1.1
5
6
SBSW,SBSR, RETURN
LOBYTE,SP
DOLO
HIBYTE,SP
LOBYTE,SP
Address:
This register contains seven flags that show the source of the last reset.
All flag bits are cleared automatically following a read of the register. The
register is initialized on power-up as shown with the POR bit set and all
other bits cleared. However, during a POR or any other internal reset,
the RST pin is pulled low. After the pin is released, it will be sampled 32
OSCDCLK cycles later. If the pin is not above a V
PIN bit in the SRSR may be set in addition to whatever other bits are set.
POR — Power-On Reset Bit
Read:
Write:
POR:
1 = Last reset caused by POR circuit
0 = Read of SRSR
$FE01
POR
Bit 7
1
Figure 8-20. SIM Reset Status Register (SRSR)
System Integration Module (SIM)
= Unimplemented
PIN
6
0
;
;
;If RETURNLO is not zero,
;then just decrement low byte.
;Else deal with high byte, too.
;Point to WAIT/STOP opcode.
;Restore H register.
See if wait mode or stop mode was exited by
break.
COP
5
0
ILOP
4
0
ILAD
3
0
System Integration Module (SIM)
IH
USB
2
0
at that time, then the
LVI
1
0
Technical Data
Bit 0
0
0
119