MC908JB16DWE Freescale Semiconductor, MC908JB16DWE Datasheet - Page 126

• Manufacturer Part Number: MC908JB16DWE
• Description: IC MCU 16K FLASH 6MHZ USB 28SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16DWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Monitor ROM (MON)
9.4.1 Entering Monitor Mode
Technical Data
126
Notes:
1. PTA3 = 0: Bypasses the divide-by-two prescaler to SIM when using V
2. See
V
V
TST
TST
V
V
DD
DD
(2)
(2)
Section 20. Electrical Specifications
(contain
BLANK
BLANK
$FF)
NOT
X
X
1
1
1
1
Table 9-1. Mode Entry Requirements and Options
Factory use only
Table 9-1
specified in the table, monitor mode may be entered after a POR and will
allow communication at 19200 baud provided one of the following sets
of conditions is met:
X
X
0
1
1. If IRQ = V
2. If $FFFE & $FFFF is blank (contains $FF):
X
X
0
0
– External clock on OSC1 is 12MHz
– PTA3 = high
– PTE3 = high
– External clock on OSC1 is 12MHz
– IRQ = V
– PTE3 = high
1
1
X
X
shows the pin conditions for entering monitor mode. As
for V
X
1
1
1
Monitor ROM (MON)
TST
TST
External Clock,
DD
voltage level requirements.
:
12 MHz
12 MHz
12 MHz
12 MHz
f
XCLK
TST
Frequency,
(f
(f
(f
for monitor mode entry.
12 MHz
XCLK
XCLK
XCLK
(f
6 MHz
6 MHz
6 MHz
f
Bus
XCLK
BUS
÷ 2)
÷ 2)
÷ 2)
)
High-voltage entry to
monitor mode.
38400 baud communication
on PTA0. COP disabled.
High-voltage entry to
monitor mode.
19200 baud communication
on PTA0. COP disabled.
Low-voltage entry to
monitor mode.
19200 baud communication
on PTA0. COP disabled.
Enters user mode.
If $FFFE and $FFFF is
blank, MCU will encounter
an illegal address reset.
MC68HC908JB16
Freescale Semiconductor
Comments
—
Rev. 1.1