MC9S12C128CFUE Freescale Semiconductor, MC9S12C128CFUE Datasheet - Page 432

• Manufacturer Part Number: MC9S12C128CFUE
• Description: IC MCU 128K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C128CFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 25MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 60
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/2.97V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: PQFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4000 B
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 61
• Number Of Timers: 1
• Operating Supply Voltage: - 0.3 V to + 6.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Chapter 14 Serial Peripheral Interface (SPIV3) Block Description
14.4.7
In run mode with the SPI system enable (SPE) bit in the SPI control register clear, the SPI system is in a
low-power, disabled state. SPI registers remain accessible, but clocks to the core of this module are
disabled.
14.4.8
SPI operation in wait mode depends upon the state of the SPISWAI bit in SPI Control Register 2.
14.4.9
Stop mode is dependent on the system. The SPI enters stop mode when the module clock is disabled (held
high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the
transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is
exchanged correctly. In slave mode, the SPI will stay synchronized with the master.
The stop mode is not dependent on the SPISWAI bit.
432
•
•
If SPISWAI is clear, the SPI operates normally when the CPU is in wait mode
If SPISWAI is set, SPI clock generation ceases and the SPI module enters a power conservation
state when the CPU is in wait mode.
— If SPISWAI is set and the SPI is configured for master, any transmission and reception in
— If SPISWAI is set and the SPI is configured as a slave, any transmission and reception in
progress stops at wait mode entry. The transmission and reception resumes when the SPI exits
wait mode.
progress continues if the SCK continues to be driven from the master. This keeps the slave
synchronized to the master and the SCK.
If the master transmits several bytes while the slave is in wait mode, the slave will continue to
send out bytes consistent with the operation mode at the start of wait mode (i.e. If the slave is
currently sending its SPIDR to the master, it will continue to send the same byte. Else if the
slave is currently sending the last received byte from the master, it will continue to send each
previous master byte).
Operation in Run Mode
Operation in Wait Mode
Operation in Stop Mode
Care must be taken when expecting data from a master while the slave is in
wait or stop mode. Even though the shift register will continue to operate,
the rest of the SPI is shut down (i.e. a SPIF interrupt will not be generated
until exiting stop or wait mode). Also, the byte from the shift register will
not be copied into the SPIDR register until after the slave SPI has exited wait
or stop mode. A SPIF flag and SPIDR copy is only generated if wait mode
is entered or exited during a tranmission. If the slave enters wait mode in idle
mode and exits wait mode in idle mode, neither a SPIF nor a SPIDR copy
will occur.
MC9S12C-Family / MC9S12GC-Family
Rev 01.24
NOTE
Freescale Semiconductor