C8051T633-GM Silicon Laboratories Inc, C8051T633-GM Datasheet - Page 58
![IC MCU 4KB 20PIN QFN](/photos/12/25/122567/silicon_laboratories_inc-20-qfn_sml.jpg)
C8051T633-GM
Manufacturer Part Number
C8051T633-GM
Description
IC MCU 4KB 20PIN QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T63xr
Specifications of C8051T633-GM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
17
Program Memory Size
4KB (4K x 8)
Program Memory Type
OTP
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
768 B
Interface Type
UART, SPI, SMBus
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
17
Number Of Timers
4 x 16-bit
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T630DK
Minimum Operating Temperature
- 40 C
For Use With
336-1464 - KIT DEV FOR C8051T630 FAMILY
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1461-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T633-GM
Manufacturer:
Silicon
Quantity:
270
C8051T630/1/2/3/4/5
The Comparator response time may be configured in software via the CPT0MD register (see SFR Defini-
tion 11.2). Selecting a longer response time reduces the Comparator supply current.
The Comparator hysteresis is software-programmable via its Comparator Control register CPT0CN. The
user can program both the amount of hysteresis voltage (referred to the input voltage) and the positive and
negative-going symmetry of this hysteresis around the threshold voltage.
The Comparator hysteresis is programmed using Bits3–0 in the Comparator Control Register CPT0CN
(shown in SFR Definition 11.1). The amount of negative hysteresis voltage is determined by the settings of
the CP0HYN bits. As shown in Figure 11.2, settings of 20, 10 or 5 mV of negative hysteresis can be pro-
grammed, or negative hysteresis can be disabled. In a similar way, the amount of positive hysteresis is
determined by the setting the CP0HYP bits.
Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Inter-
rupt enable and priority control, see Section “15.1. MCU Interrupt Sources and Vectors” on page 81). The
CP0FIF flag is set to logic 1 upon a Comparator falling-edge occurrence, and the CP0RIF flag is set to
logic 1 upon the Comparator rising-edge occurrence. Once set, these bits remain set until cleared by soft-
ware. The Comparator rising-edge interrupt mask is enabled by setting CP0RIE to a logic 1. The
Comparator0 falling-edge interrupt mask is enabled by setting CP0FIE to a logic 1.
The output state of the Comparator can be obtained at any time by reading the CP0OUT bit. The Compar-
ator is enabled by setting the CP0EN bit to logic 1, and is disabled by clearing this bit to logic 0.
Note that false rising edges and falling edges can be detected when the comparator is first powered on or
if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the
rising-edge and falling-edge flags be explicitly cleared to logic 0 a short time after the comparator is
enabled or its mode bits have been changed.
58
(Programmed with CP0HYP Bits)
Positive Hysteresis Voltage
INPUTS
OUTPUT
VIN+
VIN-
CIRCUIT CONFIGURATION
Positive Hysteresis
Figure 11.2. Comparator Hysteresis Plot
CP0-
VIN+
CP0+
VIN-
Disabled
V
OL
V
OH
+
_
CP0
Positive Hysteresis
Maximum
OUT
Rev. 1.0
Negative Hysteresis
Disabled
Negative Hysteresis
(Programmed by CP0HYN Bits)
Maximum
Negative Hysteresis Voltage