C8051T633-GM Silicon Laboratories Inc, C8051T633-GM Datasheet - Page 98
![IC MCU 4KB 20PIN QFN](/photos/12/25/122567/silicon_laboratories_inc-20-qfn_sml.jpg)
C8051T633-GM
Manufacturer Part Number
C8051T633-GM
Description
IC MCU 4KB 20PIN QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T63xr
Specifications of C8051T633-GM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
17
Program Memory Size
4KB (4K x 8)
Program Memory Type
OTP
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
768 B
Interface Type
UART, SPI, SMBus
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
17
Number Of Timers
4 x 16-bit
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T630DK
Minimum Operating Temperature
- 40 C
For Use With
336-1464 - KIT DEV FOR C8051T630 FAMILY
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1461-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T633-GM
Manufacturer:
Silicon
Quantity:
270
C8051T630/1/2/3/4/5
SFR Definition 18.1. VDM0CN: V
SFR Address = 0xFF
18.3. External Reset
The external RST pin provides a means for external circuitry to force the device into a reset state. Assert-
ing an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 5.4 for complete RST pin spec-
ifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
18.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than 100 µs, the one-shot will time out and generate a reset. After a
MCD reset, the MCDRSF flag (RSTSRC.2) will read 1, signifying the MCD as the reset source; otherwise,
this bit reads 0. Writing a 1 to the MCDRSF bit enables the Missing Clock Detector; writing a 0 disables it.
The state of the RST pin is unaffected by this reset.
98
Name
Reset
5:0
Bit
Type
7
6
Bit
VDDSTAT
VDMEN
Unused
VDMEN
Name
Varies
R/W
7
VDDSTAT
V
This bit turns the V
tem resets until it is also selected as a reset source in register RSTSRC (SFR Def-
inition 18.2). Selecting the V
may generate a system reset. In systems where this reset would be undesirable, a
delay should be introduced between enabling the V
reset source. See Table 5.4 for the minimum V
0: V
1: V
V
This bit indicates the current power supply status (V
0: V
1: V
Unused. Read = 000000b; Write = Don’t care.
Varies
DD
DD
R
6
DD
DD
DD
DD
Monitor Enable.
Status.
Monitor Disabled.
Monitor Enabled.
is at or below the V
is above the V
R
5
0
DD
DD
DD
monitor circuit on/off. The V
Monitor Control
monitor threshold.
Rev. 1.0
DD
R
4
0
DD
monitor threshold.
monitor as a reset source before it has stabilized
Function
R
3
0
DD
DD
Monitor turn-on time.
R
2
0
DD
DD
Monitor cannot generate sys-
Monitor and selecting it as a
Monitor output).
R
1
0
R
0
0