M38507F8AFP#U1 Renesas Electronics America, M38507F8AFP#U1 Datasheet - Page 33

• Manufacturer Part Number: M38507F8AFP#U1
• Description: IC 740/3850 MCU FLASH 42SSOP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M38507F8AFP#U1

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 12.5MHz
• Connectivity: SIO, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 42-SSOP
• Package: 42SSOP
• Family Name: 740
• Maximum Speed: 12.5 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: UART
• On-chip Adc: 9-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

3850 Group (Spec.A QzROM version)
Rev.2.13
REJ03B0125-0213
PWM (PWM: Pulse Width Modulation)
The 3850 group (spec.A) has a PWM function with an 8-bit
resolution, based on a signal that is the clock input X
clock input divided by 2.
• Data Setting
The PWM output pin also functions as port P4
period by the PWM prescaler, and set the “H” term of output
pulse by the PWM register.
If the value in the PWM prescaler is n and the value in the PWM
register is m (where n = 0 to 255 and m = 0 to 255):
PWM period = 255 × (n+1) / f(X
Output pulse “H” term = PWM period × m / 255
Fig 30. Block diagram of PWM function
(X
CIN
= 31.875 × (n+1) µs
= 0.125 × (n+1) × m µs
(when f(X
(when f(X
at low-speed mode)
Apr 17, 2009
IN
IN
) = 8 MHz, count source selection bit = “0”)
) = 8 MHz, count source selection bit = “0”)
X
IN
Data bus
1/2
IN
Page 31 of 56
)
“0”
Count source
selection bit
“1”
4
. Set the PWM
prescaler pre-latch
PWM prescaler
prescaler latch
IN
PWM
PWM
or that
Transfer control circuit
• PWM Operation
When bit 0 (PWM enable bit) of the PWM control register is set
to “1”, operation starts by initializing the PWM output circuit,
and pulses are output starting at an “H”.
If the PWM register or PWM prescaler is updated during PWM
output, the pulses will change in the cycle after the one in which
the change was made.
Fig 29. Timing of PWM period
register pre-latch
PWM output
register latch
PWM register
PWM
m : Contents of PWM register
n : Contents of PWM prescaler
T : PWM period (when f(X
PWM
selection bit = “0”)
31.875 × m × (n+1)
T = [31.875 × (n+1)] µs
Port P4
255
PWM function enable bit
4
IN
latch
) = 8 MHz, count source
µs
Port P4
4