AT90PWM316-16MU Atmel, AT90PWM316-16MU Datasheet - Page 58

• Manufacturer Part Number: AT90PWM316-16MU
• Description: MCU AVR 16K FLASH 16MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM316-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-QFN
• Processor Series: AT90PWMx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 2
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Cpu Family: 90P
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 1KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: QFN EP
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOICATAVRMC200 - KIT EVAL FOR AT90PWM3 ASYNCATAVRFBKIT - KIT DEMO BALLAST FOR AT90PWM2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.1.1
10.1.2
58
AT90PWM216/316
Moving Interrupts Between Application and Boot Space
MCU Control Register – MCUCR
When the BOOTRST Fuse is programmed, the Boot section size set to 2K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses in AT90PWM216/316 is:
The MCU Control Register controls the placement of the Interrupt Vector table.
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
Bit
Read/Write
Initial Value
0x002
...
0x01F
;
.org 0xC00
0xC00
0xC01
0xC02
0xC03
0xC04
0xC05
Address Labels Code
;
.org 0xC00
0xC00
0xC01
0xC02
...
0xC1F
;
0xC20
0xC21
0xC22
0xC23
0xC24
0xC25
RESET: ldi
RESET: ldi
SPIPS
R/W
7
0
rjmp
...
rjmp
out
ldi
out
sei
<instr>
rjmp
rjmp
rjmp
...
rjmp
out
ldi
out
sei
<instr>
R
6
–
0
PSC2_EC
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
PSC2_CAPT
PSC2_EC
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
xxx
xxx
R
5
–
0
PUD
R/W
4
0
; PSC2 End Cycle Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
; Reset handler
; PSC2 Capture event Handler
; PSC2 End Cycle Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
“Boot Loader Support – Read-While-Write
R
3
–
0
R
2
–
0
IVSEL
R/W
1
0
IVCE
R/W
0
0
7710E–AVR–08/10
MCUCR