AT90USB162-16AU Atmel, AT90USB162-16AU Datasheet - Page 201

• Manufacturer Part Number: AT90USB162-16AU
• Description: MCU AVR USB 16K FLASH 32-TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/USART/debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 22
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• No. Of Timers: 2
• Embedded Interface Type: SPI, USART
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

20.11.2
20.12 CONTROL endpoint management
20.12.1
7707F–AVR–11/10
STALL handshake and Retry mechanism
Control Write
The Retry mechanism has priority over the STALL handshake. A STALL handshake is sent if the
STALLRQ request bit is set and if there is no retry required.
A SETUP request is always ACK’ed. When a new setup packet is received, the RXSTPI inter-
rupt is triggered (if enabled). The RXOUTI interrupt is not triggered.
The FIFOCON and RWAL fields are irrelevant with CONTROL endpoints. The firmware shall
thus never use them on that endpoints. When read, their value is always 0.
CONTROL endpoints are managed by the following bits:
CONTROL endpoints should not be managed by interrupts, but only by polling the status bits.
The next figure shows a control write transaction. During the status stage, the controller will not
necessary send a NAK at the first IN token:
• RXSTPI is set when a new SETUP is received. It shall be cleared by firmware to
• RXOUTI is set when a new OUT data is received. It shall be cleared by firmware to
• TXINI is set when the bank is ready to accept a new IN packet. It shall be cleared by firmware
• If the firmware knows the exact number of descriptor bytes that must be read, it can then
• or it can read the bytes and poll NAKINI, which tells that all the bytes have been sent by the
USB line
RXSTPI
RXOUTI
TXINI
acknowledge the packet and to clear the endpoint bank.
acknowledge the packet and to clear the endpoint bank.
to send the packet and to clear the endpoint bank.
anticipate on the status stage and send a ZLP for the next IN token,
host, and the transaction is now in the status stage.
SETUP
SETUP
HW
SW
OUT
HW
SW
DATA
OUT
HW
AT90USB82/162
SW
NAK
IN
STATUS
SW
IN
201