AT90USB162-16AU Atmel, AT90USB162-16AU Datasheet - Page 255

• Manufacturer Part Number: AT90USB162-16AU
• Description: MCU AVR USB 16K FLASH 32-TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/USART/debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 22
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• No. Of Timers: 2
• Embedded Interface Type: SPI, USART
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

25.6.13
25.6.14
25.6.15
7707F–AVR–11/10
Reading the Signature Bytes
Reading the Calibration Byte
Parallel Programming Characteristics
Figure 25-6. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read
The algorithm for reading the Signature bytes is as follows (refer to
page 249
The algorithm for reading the Calibration byte is as follows (refer to
page 249
Figure 25-7. Parallel Programming Timing, Including some General Timing Requirements
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte (0x00 - 0x02).
3. Set OE to “0”, and BS to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
(DATA, XA0/1, BS1, BS2)
for details on Command and Address loading):
for details on Command and Address loading):
Data & Contol
Extended Fuse Byte
Fuse Low Byte
RDY/BSY
Fuse High Byte
PAGEL
XTAL1
Lock Bits
WR
t
t
BVPH
DVXH
BS2
BS2
t
t
XHXL
PHPL
0
1
0
1
t
t
t
t
XLDX
XLWL
PLBX
PLWL
t
BVWL
BS1
t
WLWH
WLRL
AT90USB82/162
0
1
“Programming the Flash” on
“Programming the Flash” on
t
WLBX
DATA
t
WLRH
255