PIC18F8310-E/PT Microchip Technology, PIC18F8310-E/PT Datasheet - Page 148

• Manufacturer Part Number: PIC18F8310-E/PT
• Description: IC PIC MCU FLASH 8KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F8310-E/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• For Use With: XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

PIC18F6310/6410/8310/8410
11.10 Parallel Slave Port
PORTD can also function as an 8-bit wide Parallel
Slave Port (PSP), or microprocessor port, when control
bit, PSPMODE (PSPCON<4>), is set. It is asynchro-
nously readable and writable by the external world
through RD control input pin, RE0/RD and WR control
input pin, RE1/WR.
The PSP can directly interface to an 8-bit micro-
processor data bus. The external microprocessor can
read or write the PORTD latch as an 8-bit latch. Setting
bit, PSPMODE, enables port pin, RE0/RD, to be the
RD input, RE1/WR to be the WR input and RE2/CS to
be the CS (Chip Select) input. For this functionality, the
corresponding data direction bits of the TRISE register
(TRISE<2:0>) must be configured as inputs (set).
A write to the PSP occurs when both the CS and WR
lines are first detected low and ends when either are
detected high. The PSPIF and IBF flag bits are both set
when the write ends.
A read from the PSP occurs when both the CS and RD
lines are first detected low. The data in PORTD is read
out and the OBF bit is set. If the user writes new data
to PORTD to set OBF, the data is immediately read out;
however, the OBF bit is not set.
When either the CS or RD lines are detected high, the
PORTD pins return to the input state and the PSPIF bit
is set. User applications should wait for PSPIF to be set
before servicing the PSP; when this happens, the IBF
and OBF bits can be polled and the appropriate action
taken.
The timing for the control signals in Write and Read
modes is shown in
respectively.
DS39635C-page 148
Note:
For PIC18F8310/8410 devices, the Parallel
Slave
Microcontroller mode.
Port
Figure 11-3
is
available
and
Figure
only
11-4,
in
FIGURE 11-2:
One bit of PORTD
Note: I/O pin has protection diodes to V
Data Bus
Set Interrupt Flag
PSPIF (PIR1<7>)
WR LATD
or
PORTD
RD PORTD
RD LATD
TRIS Latch
Data Latch
Q
D
CK
EN
EN
Q
D
PORTD AND PORTE
BLOCK DIAGRAM
(PARALLEL SLAVE
PORT)
 2010 Microchip Technology Inc.
Chip Select
Read
Write
TTL
DD
TTL
TTL
TTL
and V
SS
.
RDx
RD
CS
WR
Pin