PIC18F4580-I/P Microchip Technology, PIC18F4580-I/P Datasheet - Page 218

• Manufacturer Part Number: PIC18F4580-I/P
• Description: IC PIC MCU FLASH 16KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4580-I/P

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2480/2580/4480/4580
17.4.9
A Repeated Start condition occurs when the RSEN bit
(SSPCON2<1>) is programmed high and the I
module is in the Idle state. When the RSEN bit is set,
the SCL pin is asserted low. When the SCL pin is sam-
pled low, the Baud Rate Generator is loaded with the
contents of SSPADD<5:0> and begins counting. The
SDA pin is released (brought high) for one Baud Rate
Generator count (T
tor times out, and if SDA is sampled high, the SCL pin
will be deasserted (brought high). When SCL is sam-
pled high, the Baud Rate Generator is reloaded with
the contents of SSPADD<6:0> and begins counting.
SDA and SCL must be sampled high for one T
This action is then followed by assertion of the SDA pin
(SDA = 0) for one T
this, the RSEN bit (SSPCON2<1>) will be automatically
cleared and the Baud Rate Generator will not be
reloaded, leaving the SDA pin held low. As soon as a
Start condition is detected on the SDA and SCL pins,
the S bit (SSPSTAT<3>) will be set. The SSPIF bit will
not be set until the Baud Rate Generator has timed out.
FIGURE 17-20:
DS39637C-page 216
I
START CONDITION TIMING
2
C MASTER MODE REPEATED
Falling edge of ninth clock,
BRG
BRG
REPEAT START CONDITION WAVEFORM
). When the Baud Rate Genera-
SDA
SCL
while SCL is high. Following
end of XMIT
Write to SSPCON2
occurs here.
SDA = 1,
SCL (no change).
2
C logic
BRG
Preliminary
T
SDA = 1,
SCL = 1
.
BRG
T
BRG
Immediately following the SSPIF bit getting set, the user
may write the SSPBUF with the 7-bit address in 7-bit
mode, or the default first address in 10-bit mode. After
the first eight bits are transmitted and an ACK is
received, the user may then transmit an additional eight
bits of address (10-bit mode) or eight bits of data (7-bit
mode).
17.4.9.1
If the user writes the SSPBUF when a Repeated Start
sequence is in progress, the WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
Note:
Note 1: If RSEN is programmed while any other
Sr = Repeated Start
T
BRG
2: A bus collision during the Repeated Start
At completion of Start bit,
hardware clears RSEN bit
Set S (SSPSTAT<3>)
and sets SSPIF
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPCON2 is disabled until the Repeated
Start condition is complete.
Write to SSPBUF occurs here
event is in progress, it will not take effect.
condition occurs if:
• SDA is sampled low when SCL goes
• SCL goes low before SDA is
WCOL Status Flag
T
from low-to-high.
asserted low. This may indicate that
another master is attempting to
transmit a data ‘1’.
BRG
1st bit
T
BRG
© 2007 Microchip Technology Inc.