ADUC7128BCPZ126 Analog Devices Inc, ADUC7128BCPZ126 Datasheet - Page 25

• Manufacturer Part Number: ADUC7128BCPZ126
• Description: IC DAS MCU ARM7 ADC/DDS 64-LFCSP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7128BCPZ126

• Core Size: 16/32-Bit
• Program Memory Size: 126KB (126K x 8)
• Core Processor: ARM7
• Speed: 41.78MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: PLA, POR, PWM, PSM, Temp Sensor, WDT
• Number Of I /o: 28
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x12b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LFCSP
• Controller Family/series: (ARM7) ADUC
• No. Of I/o's: 40
• Ram Memory Size: 8KB
• Cpu Speed: 41.78MHz
• No. Of Timers: 5
• No. Of Pwm Channels: 6
• Package: 64LFCSP EP
• Device Core: ARM7TDMI
• Family Name: ADuC7xxx
• Maximum Speed: 41.78 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 40
• Interface Type: I2C/SPI/UART
• On-chip Adc: 14-chx12-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADUC7128QSPZ - KIT DEV FOR ADUC7128
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

OVERVIEW OF THE ARM7TDMI CORE
The ARM7 core is a 32-bit reduced instruction set computer
(RISC). It uses a single 32-bit bus for instruction and data. The
length of the data can be 8 bits, 16 bits, or 32 bits. The length of
the instruction word is 32 bits.
The ARM7TDMI is an ARM7 core with the following four
additional features:
•
•
•
•
THUMB MODE (T)
An ARM® instruction is 32-bits long. The ARM7TDMI processor
supports a second instruction set that has been compressed into
16-bits, called the Thumb instruction set. Faster execution from
16-bit memory and greater code density can usually be achieved
by using the Thumb instruction set instead of the ARM instruction
set, which makes the ARM7TDMI core particularly suitable for
embedded applications.
However, the Thumb mode has two limitations:
•
•
See the ARM7TDMI user guide for details on the core
architecture, the programming model, and both the ARM
and Thumb instruction sets.
LONG MULTIPLY (M)
The ARM7TDMI instruction set includes four extra instruc-
tions that perform 32-bit by 32-bit multiplication with 64-bit
result, and 32-bit by 32-bit multiplication-accumulation (MAC)
with 64-bit result. This result is achieved in fewer cycles than
required on a standard ARM7 core.
EMBEDDEDICE (I)
EmbeddedICE provides integrated on-chip support for the core.
The EmbeddedICE module contains the breakpoint and watch-
point registers that allow code to be halted for debugging purposes.
These registers are controlled through the JTAG test port.
When a breakpoint or watchpoint is encountered, the processor
halts and enters debug state. Once in a debug state, the processor
registers can be inspected, as well as the Flash/EE, the SRAM,
and the memory mapped registers.
T, support for the Thumb® (16-bit) instruction set
D, support for debug
M, support for long multiplications
I, includes the embedded ICE module to support
embedded system debugging
Thumb code typically requires more instructions for the
same job. As a result, ARM code is usually best for
maximizing the performance of the time-critical code.
The Thumb instruction set does not include some of the
instructions needed for exception handling, which auto-
matically switches the core to ARM code for exception
handling.
Rev. 0 | Page 25 of 92
EXCEPTIONS
ARM supports five types of exceptions and a privileged processing
mode for each type. The five types of exceptions are
•
•
•
•
•
Typically, the programmer defines interrupt as IRQ, but for
higher priority interrupt, that is, faster response time, the
programmer can define interrupt as FIQ.
ARM REGISTERS
ARM7TDMI has a total of 37 registers: 31 general-purpose
registers and six status registers. Each operating mode has
dedicated banked registers.
When writing user-level programs, 15 general-purpose, 32-bit
registers (R0 to R14), the program counter (R15), and the current
program status register (CPSR) are usable. The remaining registers
are used only for system-level programming and exception
handling.
When an exception occurs, some of the standard registers are
replaced with registers specific to the exception mode. All
exception modes have replacement banked registers for the
stack pointer (R13) and the link register (R14), as represented
in Figure 28. The fast interrupt mode has more registers (R8 to
R12) for fast interrupt processing. Interrupt processing can begin
without the need to save or restore these registers and, thus,
saves critical time in the interrupt handling process.
More information relative to the programmer’s model and the
ARM7TDMI core architecture can be found in the following
ARM7TDMI technical and ARM architecture manuals available
directly from ARM Ltd.:
•
•
Normal interrupt or IRQ. This is provided to service
general-purpose interrupt handling of internal and
external events.
Fast interrupt or FIQ. This is provided to service data
transfer or communication channel with low latency.
FIQ has priority over IRQ.
Memory abort.
Attempted execution of an undefined instruction.
Software interrupt instruction (SWI). This can be used to
make a call to an operating system.
DDI0029G, ARM7TDMI Technical Reference Manual
DDI-0100, ARM Architecture Reference Manual
ADuC7128/ADuC7129