ST7FLITE20F1B6 STMicroelectronics, ST7FLITE20F1B6 Datasheet - Page 75

• Manufacturer Part Number: ST7FLITE20F1B6
• Description: IC MCU 8BIT 8K FLASH 20-DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE20F1B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ST7FLITE2x
• Core: ST7
• Data Bus Width: 8 bit
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5517 - EVAL BOARD 1PHASE ENERGY METER497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

/* Program Start */
#include "ST7lib_config.h"
#include "main.h"
void main(void);
void main(void)
{
unsigned char NbOfBytes_get = 10;
unsigned char NbOfBytes_put = 10;
unsigned char Rx_Data;
unsigned char Buff_Test[buf_size];
unsigned char Buff[buf_size] ={0x00,0x55,0xAA,0xFF,0x00,0x55,0xAA,0xFF,0x00,0x55};
SPI_TxErrCode_t Temp1= 0x00 ;
SPI_RxErrCode_t Temp2= 0x00 ;
SPI_Init((((unsigned char)SPI_DEFAULT | ((unsigned char)SPI_ENABLE|
EnableInterrupts
/*=========================================================================
=========================================================================*/
#ifdef SPI_POLLING_TX
SPI_PutByte (My_Data) ;
Temp1 = SPI_IsTransmitCompleted();
while ((!(User_Timeout_Function())) && (Temp1 != SPI_TRANSMIT_OK) )
{
}
if (!(User_Timeout_Function()))
{
}
switch(SPI_PutBuffer(Buff, (unsigned char)10))
{
Transmission through ‘Polling’ mode
Temp1 = SPI_IsTransmitCompleted() ;
switch (Temp1)
{
}
/* Transmission of 10 data bytes from user buffer */
case (SPI_TX_MODF + SPI_TX_WCOL):
/* Declaration of prototypes of user defined functions used in main.c */
((unsigned char)SPI_ENABLE_IT|((unsigned char)SPI_BAUDRATE_4|
((unsigned char)SPI_CLK_PP_0)))))), SPI_MSTR_SW );
/* SPI Initialised in master software mode,Serial peripheral output
/* Single byte data transmission */
case (SPI_TX_MODF + SPI_TX_WCOL):
case (SPI_TX_MODF):
case (SPI_TX_WCOL):
default:
enabled, Interrupt enabled, CPOL=0, CPHA=1 and baudrate is 2MHz */
User_Function();
break;
User_Function();
break;
/* Interrupt mask is reset for enabling interrupt */
/*List of all ST7 devices and communication mode */
/* If none of the above condition is met */
Function Descriptions
/* Error Management */
75/235