MC908GT16CBE Freescale Semiconductor, MC908GT16CBE Datasheet - Page 117

• Manufacturer Part Number: MC908GT16CBE
• Description: IC MCU 16K FLASH 8MHZ SPI 42SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GT16CBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Controller Family/series: HC08
• No. Of I/o's: 34
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GT
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 30
• Number Of Timers: 4
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Package: 42SPDIP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 11
Low-Power Modes (MODES)
11.1 Introduction
The microcontroller (MCU) may enter two low-power modes: wait mode and stop mode. They are
common to all HC08 MCUs and are entered through instruction execution. This section describes how
each module acts in the low-power modes.
11.1.1 Wait Mode
The WAIT instruction puts the MCU in a low-power standby mode in which the central processor unit
(CPU) clock is disabled but the bus clock continues to run. Power consumption can be further reduced by
disabling the LVI module and/or the timebase module through bits in the CONFIG1 register. (See
Chapter 4 Configuration Register
(CONFIG).)
11.1.2 Stop Mode
Stop mode is entered when a STOP instruction is executed. The CPU clock is disabled and the bus clock
is disabled if the OSCENINSTOP bit in the CONFIG2 register is at a 0. (See
Chapter 4 Configuration
Register
(CONFIG).)
11.2 Analog-to-Digital Converter (ADC)
11.2.1 Wait Mode
The analog-to-digital converter (ADC) continues normal operation during wait mode. Any enabled CPU
interrupt request from the ADC can bring the MCU out of wait mode. If the ADC is not required to bring
the MCU out of wait mode, power down the ADC by setting ADCH4–ADCH0 bits in the ADC status and
control register before executing the WAIT instruction.
11.2.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction. Any pending conversion is aborted.
ADC conversions resume when the MCU exits stop mode after an external interrupt. Allow one
conversion cycle to stabilize the analog circuitry.
11.3 Break Module (BRK)
11.3.1 Wait Mode
If enabled, the break (BRK) module is active in wait mode. In the break routine, the user can subtract one
from the return address on the stack if the SBSW bit in the break status register is set.
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Freescale Semiconductor
117