M30290FAHP#U5A Renesas Electronics America, M30290FAHP#U5A Datasheet - Page 188

• Manufacturer Part Number: M30290FAHP#U5A
• Description: IC M16C/29 MCU FLASH 96K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/29r

Specifications of M30290FAHP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Size: 96KB (96K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 27x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R
R
e
E
. v
J
Table 13.8 Single-phase Waveform Output Mode Specifications
Waveform output start condition
Waveform output stop condition
Interrupt request
OUTC1j pin
Selectable function
NOTE:
0
Output waveform
13.5.1 Single-Phase Waveform Output Mode
1
9
1 .
B
Output signal level of the OUTC1j pin becomes high ("H") when the INV bit in the G1POCRj (j=0 to 7)
register is set to 0(output is not reversed) and the base timer value matches the G1POj (j=0 to 7) register
value. The "H" signal switches to a low-level ("L") signal when the base timer reaches 0000
lists specifications of single-phase waveform mode. Figure 13.22 lists an example of single-phase wave-
form mode operation.
1. Pins OUTC1
0
2
1
M
0
1
r a
0 -
3 .
1
, 0
1
(1)
Item
2
2
0
0
0
7
to OUTC1
page 162
7
.
f o
4
• Free-running operation
• The base timer is cleared to 0000
The IFEj bit in the G1FE register is set to 1 (channel j function enabled)
The IFEj bit is set to 0 (channel j function disabled)
The G1IRj bit in the G1IR register is set to 1 when the base timer value
matches the G1POj register value (See Figure 13.22)
Pulse signal output pin
• Default value set function: Set starting waveform output level
• Inverse output function: Waveform output signal is inversed and provided
5
Cycle
following register
(a) G1PO0 register (enabled by setting RST1 bit to 1, and RST4 and RST2 bits to 0), or
(b) G1BTRR register (enabled by setting RST4 bit to 1, and RST2 and RST1 bits to 0)
(bits RST1, RST2, and RST4 of registers G1BCR1 and G1BCR0 are set to 0
(no reset))
Default output level width :
Inverse level width
Cycle
Default output level width :
Inverse level width
from the OUTC1j pin
8
m : setting value of the G1POj register (j=0 to 7), 0001
n : setting value of the G1PO0 register or the G1BTRR register, 0001
:
:
:
65536-m
n+2-m
65536
f
n+2
f
f
f
f
m
BT1
BT1
BT1
BT1
m
BT1
f
BT1
:
Specification
16
by matching the base timer with either
16
to FFFD
16
16
. Table 13.8
16
to FFFD
16