SAF-XC886CLM-8FFI 5V AC Infineon Technologies, SAF-XC886CLM-8FFI 5V AC Datasheet - Page 62

• Manufacturer Part Number: SAF-XC886CLM-8FFI 5V AC
• Description: IC MCU 8BIT FLASH TQFP-48
• Manufacturer: Infineon Technologies
• Series: XC8xxr

Specifications of SAF-XC886CLM-8FFI 5V AC

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-TFQFP
• Core Processor: XC800
• Core Size: 8-Bit
• Speed: 103.2MHz
• Connectivity: CAN, LIN, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 1.75K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 8 bit
• Data Ram Size: 1.75 KB
• Interface Type: JTAG/SPI/SSC/UART
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: MCBXC88X - BOARD EVAL FOR INFINEON XC88X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: FX886CLM8FFI5VACXT; SAF-XC886CLM-8FFI AB; SAF-XC886CLM-8FFI AB; SAFXC886CLM8FFIABT; SP000217341

3.3.3
For the P-Flash banks, a programmed wordline (WL) must be erased before it can be
reprogrammed as the Flash cells can only withstand one gate disturb. This means that
the entire sector containing the WL must be erased since it is impossible to erase a
single WL.
For the D-Flash bank, the same WL can be programmed twice before erasing is required
as the Flash cells are able to withstand two gate disturbs. This means if the number of
data bytes that needs to be written is smaller than the 32-byte minimum programming
width, the user can opt to program this number of data bytes (x; where x can be any
integer from 1 to 31) first and program the remaining bytes (32 - x) later. Hence, it is
possible to program the same WL, for example, with 16 bytes of data two times (see
Figure
Figure 12
Note: When programming a D-Flash WL the second time, the previously programmed
Data Sheet
Flash memory cells (whether 0s or 1s) should be reprogrammed with 0s to retain
its original contents and to prevent “over-programming”.
0000 ….. 0000
0000 ….. 0000
1111 ….. 0000
12)
Flash Programming Width
Flash memory cells
D-Flash Programming
32 bytes (1 WL)
H
H
H
0000 ….. 0000
1111 ….. 1111
1111 ….. 1111
H
H
H
Program 1
Program 2
55
0000 ….. 0000
1111 ….. 0000
Note: A Flash memory cell can be programmed
16 bytes
32-byte write buffers
from 0 to 1, but not from 1 to 0.
Functional Description
H
H
XC886/888CLM
1111 ….. 1111
0000 ….. 0000
16 bytes
V1.2, 2009-07
H
H