PIC16LC774/PQ Microchip Technology, PIC16LC774/PQ Datasheet - Page 58

• Manufacturer Part Number: PIC16LC774/PQ
• Description: IC MCU OTP 4KX14 A/D PWM 44-MQFP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC774/PQ

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-MQFP, 44-PQFP
• Processor Series: PIC16LC
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, SSP, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC16C77X
determine when the transmission/reception has com-
pleted. The SSPBUF must be read and/or written. If the
interrupt method is not going to be used, then software
polling can be done to ensure that a write collision does
not occur.
SSPBUF (SSPSR) for data transmission.
EXAMPLE 8-1:
LOOP BTFSS SSPSTAT, BF
The SSPSR is not directly readable or writable, and can
only be accessed by addressing the SSPBUF register.
Additionally, the MSSP status register (SSPSTAT) indi-
cates the various status conditions.
8.1.2
To enable the serial port, MSSP Enable bit, SSPEN
(SSPCON<5>) must be set. To reset or reconfigure SPI
mode, clear bit SSPEN, re-initialize the SSPCON reg-
isters, and then set bit SSPEN. This configures the
FIGURE 8-5:
DS30275A-page 58
BSF
GOTO
BCF
MOVF
MOVWF RXDATA
MOVF
MOVWF SSPBUF
ENABLING SPI I/O
Example 8-1
STATUS, RP0
LOOP
STATUS, RP0
SSPBUF, W
TXDATA, W
SPI Master SSPM3:SSPM0 = 00xxb
SPI MASTER/SLAVE CONNECTION
LOADING THE SSPBUF
(SSPSR) REGISTER
MSb
PROCESSOR 1
Serial Input Buffer
shows the loading of the
Shift Register
(SSPBUF)
(SSPSR)
;Specify Bank 1
;Has data been
;received
;(transmit
;complete)?
;No
;Specify Bank 0
;W reg = contents
;of SSPBUF
;Save in user RAM
;W reg = contents
; of TXDATA
;New data to xmit
LSb
Advance Information
SDO
SCK
SDI
Serial Clock
SDI, SDO, SCK, and SS pins as serial port pins. For the
pins to behave as the serial port function, some must
have their data direction bits (in the TRIS register)
appropriately programmed. That is:
• SDI is automatically controlled by the SPI module
• SDO must have TRISC<5> cleared
• SCK (Master mode) must have TRISC<3>
• SCK (Slave mode) must have TRISC<3> set
• SS must have TRISA<5> set
Any serial port function that is not desired may be over-
ridden by programming the corresponding data direc-
tion (TRIS) register to the opposite value.
8.1.3
Figure 8-5
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge, and latched on the opposite edge
of the clock. Both processors should be programmed to
same Clock Polarity (CKP), then both controllers would
send and receive data at the same time. Whether the
data is meaningful (or dummy data) depends on the
application software. This leads to three scenarios for
data transmission:
• Master sends data — Slave sends dummy data
• Master sends data — Slave sends data
• Master sends dummy data — Slave sends data
cleared
SDO
SCK
SDI
TYPICAL CONNECTION
shows a typical connection between two
SPI Slave SSPM3:SSPM0 = 010xb
MSb
Serial Input Buffer
Shift Register
PROCESSOR 2
(SSPBUF)
(SSPSR)
1999 Microchip Technology Inc.
LSb