AT90CAN128-16MI Atmel, AT90CAN128-16MI Datasheet - Page 40

• Manufacturer Part Number: AT90CAN128-16MI
• Description: IC MCU AVR FLASH 128K 64-QFN
• Manufacturer: Atmel
• Series: AVR® 90CANr

Specifications of AT90CAN128-16MI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• For Use With: ATDVK90CAN1 - KIT DEV FOR AT90CAN128 MCU
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

5.5
40
Low-frequency Crystal Oscillator
AT90CAN32/64/128
Table 5-4.
Notes:
To use a 32.768 kHz watch crystal as the clock source for the device, the low-frequency crystal
Oscillator must be selected by setting the CKSEL Fuses to “0100”, “0101”, “0110”, or “0111”.
The crystal should be connected as shown in
Figure 5-3.
12-22 pF capacitors may be necessary if the parasitic impedance (pads, wires & PCB) is very
low.
CKSEL0
0
0
0
0
1
1
1
1
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
SUT1..0
Start-up Times for the Oscillator Clock Selection
Low-frequency Crystal Oscillator Connections
00
01
10
00
01
10
11
11
Start-up Time from
Power-down and
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
16K CK
16K CK
16K CK
32.768 KHz
(2)
(2)
(2)
(1)
(1)
12 - 22 pF
12 - 22 pF
Figure
Additional Delay
14 CK + 4.1 ms
14 CK + 4.1 ms
14 CK + 4.1 ms
14 CK + 65 ms
14 CK + 65 ms
14 CK + 65 ms
(V
from Reset
5-3.
CC
14 CK
14 CK
= 5.0V)
XTAL2
XTAL1
GND
Recommended Usage
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Crystal Oscillator, BOD
enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator, slowly
rising power
7679H–CAN–08/08