SAF-XC167CI-32F20F BB-A Infineon Technologies, SAF-XC167CI-32F20F BB-A Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAF-XC167CI-32F20F BB-A
Manufacturer Part Number
SAF-XC167CI-32F20F BB-A
Description
IC MCU 16BIT 256KB TQFP-144-19
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC167CI-32F20F_BB-A.pdf
(90 pages)
Specifications of SAF-XC167CI-32F20F BB-A
Core Processor
C166SV2
Core Size
16-Bit
Speed
20MHz
Connectivity
CAN, EBI/EMI, I²C, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 16x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LFQFP
For Use With
B158-H8963-X-X-7600IN - KIT EASY XC167CIMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
FX167CI32F20FBBANT
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
5) Several pipeline optimizations are not active within the external IO area. This is necessary to control external
3.2
All of the external memory accesses are performed by a particular on-chip External Bus
Controller (EBC). It can be programmed either to Single Chip Mode when no external
memory is required, or to one of four different external memory access modes
are as follows:
•
•
•
•
In the demultiplexed bus modes, addresses are output on PORT1 and data is
input/output on PORT0 or P0L, respectively. In the multiplexed bus modes both
addresses and data use PORT0 for input/output. The high order address (segment) lines
use Port 4. The number of active segment address lines is selectable, restricting the
external address space to 8 Mbytes … 64 Kbytes. This is required when interface lines
are assigned to Port 4.
Up to 5 external CS signals (4 windows plus default) can be generated in order to save
external glue logic. External modules can directly be connected to the common
address/data bus and their individual select lines.
Access to very slow memories or modules with varying access times is supported via a
particular ‘Ready’ function. The active level of the control input signal is selectable.
A HOLD/HLDA protocol is available for bus arbitration and allows the sharing of external
resources with other bus masters. The bus arbitration is enabled by software. After
enabling, pins P6.7 … P6.5 (BREQ, HLDA, HOLD) are automatically controlled by the
EBC. In Master Mode (default after reset) the HLDA pin is an output. In Slave Mode pin
HLDA is switched to input. This allows the direct connection of the slave controller to
another master controller without glue logic.
Important timing characteristics of the external bus interface have been made
programmable (via registers TCONCSx/FCONCSx) to allow the user the adaption of a
wide range of different types of memories and external peripherals.
In addition, up to 4 independent address windows may be defined (via registers
ADDRSELx) which control the access to different resources with different bus
characteristics. These address windows are arranged hierarchically where window 4
overrides window 3, and window 2 overrides window 1. All accesses to locations not
covered by these 4 address windows are controlled by TCONCS0/FCONCS0. The
currently active window can generate a chip select signal.
1) Bus modes are switched dynamically if several address windows with different mode settings are used.
Data Sheet
peripherals properly.
16 … 24-bit Addresses, 16-bit Data, Demultiplexed
16 … 24-bit Addresses, 16-bit Data, Multiplexed
16 … 24-bit Addresses, 8-bit Data, Multiplexed
16 … 24-bit Addresses, 8-bit Data, Demultiplexed
External Bus Controller
24
Functional Description
XC167CI-32F
Derivatives
V1.1, 2006-08
1)
, which