SAF-XC167CI-32F20F BB-A Infineon Technologies, SAF-XC167CI-32F20F BB-A Datasheet - Page 62
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAF-XC167CI-32F20F BB-A
Manufacturer Part Number
SAF-XC167CI-32F20F BB-A
Description
IC MCU 16BIT 256KB TQFP-144-19
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC167CI-32F20F_BB-A.pdf
(90 pages)
Specifications of SAF-XC167CI-32F20F BB-A
Core Processor
C166SV2
Core Size
16-Bit
Speed
20MHz
Connectivity
CAN, EBI/EMI, I²C, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 16x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LFQFP
For Use With
B158-H8963-X-X-7600IN - KIT EASY XC167CIMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
FX167CI32F20FBBANT
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
Table 11
Parameter
Configuration pull-
down current
Level inactive hold
current
Level active hold
current
XTAL1, XTAL3 input
current
Pin capacitance
(digital inputs/outputs)
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
2) If XTAL1 is driven by a crystal, reaching an amplitude (peak to peak) of 0.4 ×
3) If XTAL3 is driven by a crystal, reaching an amplitude (peak to peak) of 0.25 ×
4) This parameter is tested for P2, P3, P4, P6, P7, P9.
5) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
6) As a rule, with decreasing output current the output levels approach the respective supply level (
7) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
8) An additional error current (
9) The driver of P3.15 is designed for faster switching, because this pin can deliver the reference clock for the
10) This specification is valid during Reset for configuration on RD, WR, EA, PORT0.
11) The maximum current may be drawn while the respective signal line remains inactive.
12) The minimum current must be drawn to drive the respective signal line active.
13) This specification is valid during Reset for configuration on ALE.
14) This specification is valid during Reset for pins P6.4-0, which can act as CS outputs.
15) Not subject to production test - verified by design/characterization.
Data Sheet
For signal levels outside these specifications, also refer to the specification of the overload current
Table
V
output will float and the voltage results from the external circuitry.
the definition of the overload coupling factor
bus interface (CLKOUT). The maximum leakage current for P3.15 is, therefore, increased to 1 µA.
The pull-ups on RD and WR (WRL/WRH) are also active during bus hold.
The pull-down on ALE is also active during bus hold.
The pull-ups on CS outputs are also active during bus hold.
The pull-up on pin HLDA is active when arbitration is enabled and the EBC operates in slave mode.
OH
→
14)
14)
12,
V
DDP
Current Limits for Port Output
). However, only the levels for nominal output currents are guaranteed.
13)
DC Characteristics (Operating Conditions apply)
15)
I
Symbol
I
I
I
I
I
C
INJ
CPDL
CPDH
LHI
LHA
IL
IO
) will flow if an overload current flows through an adjacent pin. Please refer to
11)
12)
11)
12)
CC –
CC –
Drivers. The limit for pin groups must be respected.
K
OV
Min.
–
120
–
-100
.
60
Limit Values
Max.
10
–
-10
–
±20
10
V
Unit Test Condition
µA
µA
µA
µA
µA
pF
1)
Electrical Parameters
V
DDI
DDI
(cont’d)
is sufficient.
is sufficient.
V
V
V
V
V
0 V <
–
IN
IN
OUT
DDP
OUT
XC167CI-32F
=
=
Derivatives
V1.1, 2006-08
= 0.5 ×
= 0.45 V
V
V
V
ILmax
IHmin
IN
V
<
OL
I
OV
V
→
.
DDI
V
SS
,